Nissan X-Trail 32. Manual — part 2156
TM-582
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
P0715 INPUT SPEED SENSOR A
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK TCM INPUT SIGNALS
1.
Connect all of disconnected connectors.
2.
Lift the vehicle.
3.
Start the engine.
4.
Check frequency of primary speed sensor.
Is the inspection result normal?
YES >> INSPECTION
END
NO
>> Replace primary speed sensor. Refer to
TM-686, "Removal and Installation"
6.
ETECT MALFUNCTIONING ITEMS
Check the following items:
• Open circuit or short circuit in harness between ignition switch and primary speed sensor harness connector
terminal 3. Refer to
PG-52, "Wiring Diagram - IGNITION POWER SUPPLY -"
• 10A fuse [No. 57, located in the fuse block (J/B)]. Refer to
PG-84, "Fuse, Connector and Terminal Arrange-
.
Is the check result normal?
YES
>> INSPECTION END
NO
>> Repair or replace malfunctioning parts.
Primary speed sensor
—
Continuity
Connector
Terminal
F55
2
Ground
Not existed
+
−
Condition
Frequency
(Approx.)
TCM
Connector
Terminal
F119
35
Ground
• Shift position: “M1” position
• Vehicle speed: 20 km/h (12 MPH)
700 Hz
JSDIA1905GB
P0717 INPUT SPEED SENSOR A
TM-583
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0717 INPUT SPEED SENSOR A
DTC Description
INFOID:0000000010622805
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector (Input speed sensor circuit is open or shorted)
• Input speed sensor
FAIL-SAFE
• Start is slow
• Acceleration is slow
• Lock-up is not performed
• Stop/start system prohibited
• Restart the engine during the stop/start system operation
• Turn OFF the electric oil pump relay
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Start the engine.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0717
INPUT SPEED SENSOR A
(Input/Turbine Speed Sensor “A” Circuit No
Signal)
When 1 is satisfied and any of 2, 3 or 4 is satisfied:
1.
When the following conditions are satisfied:
-
TCM power supply voltage: More than 11 V
-
After range change completion, it spends 2 seconds or more.
2.
When all of the following conditions are satisfied and this state is main-
tained for 5 seconds:
-
Primary pulley speed: 500 rpm or more
-
Input speed: Less than 150 rpm
-
Range: Other than P, N
-
P0715 is not detected
3.
When all of the following conditions are satisfied and this state is main-
tained for 0.5 seconds:
-
10-msec-ago input speed: 1,000 rpm or more
-
Now input speed: 0 rpm
4.
When all of the following conditions are satisfied and this state is main-
tained for 5 seconds:
-
Range: D or L
-
Engine speed: 450 rpm or more
-
Input peed: 300 rpm or more
-
Primary pulley speed: 300 rpm or more
-
Secondary pulley seed: 300 rpm or more
-
Differences between engine speed and primary pulley speed: 1,000
rpm or less
-
Differences between primary pulley speed and input speed: More than
1,000 rpm
-
Differences between engine speed and input speed: More than 1,000
rpm
-
Lock-up command is being given (except for slip lock-up)
-
DTC other than the applicable DTC is not detected.
TM-584
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
P0717 INPUT SPEED SENSOR A
2.
Drive the vehicle.
3.
Maintain the following conditions for 10 seconds or more.
4.
Stop the vehicle.
5.
Check the first trip DTC.
Is “P0717” detected?
YES
>> Go to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010622806
1.
CHECK INPUT SPEED SENSOR POWER CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect input speed sensor connector.
3.
Turn ignition switch ON.
4.
Check voltage between input speed sensor harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 6.
2.
CHECK INPUT SPEED SENSOR GROUND CIRCUIT
Check continuity between input speed sensor harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK CIRCUIT BETWEEN INPUT SPEED SENSOR AND TCM (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between input speed sensor harness connector terminal and TCM harness connector
terminal.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CHECK CIRCUIT BETWEEN INPUT SPEED SENSOR AND TCM (PART 2)
Check continuity between input speed sensor harness connector terminal and ground.
Selector lever
: “D” position
Engine speed
: 1,200 rpm or more
Vehicle speed
: 40 km/h (25 MPH) or more
+
−
Voltage
Input speed sensor
Connector
Terminal
F128
3
Ground
10 – 16 V
Input speed sensor
—
Continuity
Connector
Terminal
F128
1
Ground
Existed
Input speed sensor
TCM
Continuity
Connector
Terminal
Connector
Terminal
F128
2
F119
24
Existed
P0717 INPUT SPEED SENSOR A
TM-585
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK TCM INPUT SIGNALS
1.
Connect all of disconnected connectors.
2.
Lift the vehicle.
3.
Start the engine.
4.
Check frequency of input speed sensor.
Is the inspection result normal?
YES >> INSPECTION
END
NO
>> Replace input speed sensor. Refer to
TM-684, "Removal and Installation"
6.
ETECT MALFUNCTIONING ITEMS
Check the following items:
• Open circuit or short circuit in harness between ignition switch and input speed sensor harness connector
terminal 3. Refer to
PG-52, "Wiring Diagram - IGNITION POWER SUPPLY -"
.
• 10A fuse [No. 57, located in the fuse block (J/B)]. Refer to
PG-84, "Fuse, Connector and Terminal Arrange-
.
Is the check result normal?
YES
>> INSPECTION END
NO
>> Repair or replace malfunctioning parts.
Input speed sensor
—
Continuity
Connector
Terminal
F128
2
Ground
Not existed
+
−
Condition
Frequency
(Approx.)
TCM
Connector
Terminal
F119
24
Ground
• Shift position: “M1” position
• Vehicle speed: 20 km/h (12 MPH)
880 Hz
JSDIA3769GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст