Nissan X-Trail 32. Manual — part 2222
ROAD WHEEL TIRE ASSEMBLY
WT-61
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
REMOVAL AND INSTALLATION
ROAD WHEEL TIRE ASSEMBLY
Exploded View
INFOID:0000000010715122
Removal and Installation
INFOID:0000000010715123
REMOVAL
1.
Remove wheel nuts.
2.
Remove tire assembly.
INSTALLATION
Note the following, install in the reverse order of removal.
• When replacing or rotating wheels, perform following;
- Perform the ID registration. Refer to
.
- Perform TPMS reset operation. Refer to
Inspection
INFOID:0000000010715124
1.
Check tires for wear and improper inflation.
2.
Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a.
Remove tire from aluminum wheel and mount on a tire balance machine.
b.
Set dial indicator as shown in the figure.
c.
Check runout, if the axial runout
or radial runout
exceeds
the limit, replace aluminum wheel.
Tire assembly
: N·m (kg-m, ft-lb)
JSGIA0639GB
Limit
Axial runout
: Refer to
.
Radial runout
: Refer to
.
SEIA0737E
WT-62
< REMOVAL AND INSTALLATION >
TIRE PRESSURE SENSOR
TIRE PRESSURE SENSOR
Exploded View
INFOID:0000000010715125
Removal and Installation
INFOID:0000000010715126
REMOVAL
1.
Remove tire assembly. Refer to
WT-61, "Removal and Installation"
2.
Remove valve cap, valve core and then deflate tire.
NOTE:
If the tire is reused, apply a matching mark to the position of the tire road wheel valve hole for the purpose
of wheel balance adjustment after installation.
3.
Remove valve nut retaining tire pressure sensor and allow tire pressure sensor to fall into tire.
4.
Use the tire changer and disengage the tire beads.
CAUTION:
• Verify that the tire pressure sensor
is at the bottom of
the tire while performing the above.
• Never damage the road wheel or tire pressure sensor.
5.
Apply bead cream or an equivalent to the tire beads.
6.
Set tire onto the tire changer turntable so that the tire pressure
sensor inside the tire is located close to the road wheel valve
hole.
Tire pressure sensor
Washer/Seal
Valve nut
Valve core
Valve cap
Valve stem assembly
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
:
Parts that are replaced as a set when the tire is replaced.
JMEIA0210GB
JPEIC0104ZZ
TIRE PRESSURE SENSOR
WT-63
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
7.
Turn tire so that valve hole is at bottom and bounce so that tire
pressure sensor
is near valve hole. Carefully lift tire onto turn-
table and position valve hole (and tire pressure sensor) 270
degree from mounting/dismounting head
.
CAUTION:
Never damage the road wheel and tire pressure sensor.
8.
Remove tire pressure sensor from tire.
9.
Remove the grommet seal.
10. Remove valve stem in the direction (
).
INSTALLATION
CAUTION:
Replace valve stem assembly if the valve stem has deformations, cracks, damage or corrosion.
1.
Apply bead cream or an equivalent to the tire beads.
2.
Install the tire inside beads
onto the road wheel
in the posi-
tion shown in the figure.
3.
Install valve stem to tire pressure sensor.
4.
Install grommet seal to the tire pressure sensor assembly.
CAUTION:
• Never reuse grommet seal.
• Insert grommet seal all the way to the base.
5.
Follow the procedure below and install the tire pressure sensor to the road wheel.
a.
When valve stem assembly is replaced.
i.
Set valve stem in the tire pressure sensor.
ii.
Install the washer
in the valve stem, and then install seal
in
the valve stem.
CAUTION:
• Direction of the seal is checked.
JPEIC0014GB
JSEIA0378ZZ
JPEIC0105ZZ
: Upper side
JMEIA0211ZZ
WT-64
< REMOVAL AND INSTALLATION >
TIRE PRESSURE SENSOR
• The cut part
of washer becomes in the center of valve
stem.
b.
Check the condition of valve stem before installing tire pressure
sensor to road wheel.
CAUTION:
The base of valve stem
must be positioned in the groove
of the metal plate as shown in the figure.
c.
Hold tire pressure sensor as shown in the figure, and press the sensor in the direction shown by arrow
(
) to bring it into absolute contact with road wheel. After this, tighten valve nut to the specified torque.
CAUTION:
• Never reuse valve core and valve cap.
• Check that grommet seal is free of foreign matter.
• Check that grommet seal contacts horizontally with road wheel.
• Check again that the base of valve stem is positioned in the groove of the metal plate.
• Manually tighten valve nut all the way to the wheel. (Never use a power tool to avoid impact.)
JMEIA0212ZZ
JSEIA0376GB
JSEIA0465GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст