Nissan X-Trail 32. Manual — part 1068
AIR CLEANER FILTER
EM-169
< PERIODIC MAINTENANCE >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Removal and Installation
INFOID:0000000010783772
REMOVAL
1.
To remove air duct 2
, pinch pawl
to unlock, move pawl
frontward, and remove air duct 2 upward.
2.
Remove the clips
of air cleaner cover
.
3.
Shift air cleaner cover
to car front side and remove air cleaner
element .
INSTALLATION
Install in the reverse order of removal.
• Insert the projection
of air cleaner element
in such a way so
that it becomes the position (upper front side of car) of illustration.
• Verify that there is no looseness in air cleaner cover and has been fixed accurately.
: Vehicle front
JSBIA4626ZZ
: Vehicle front
JPBIA6829ZZ
: Projection
JPBIA6830ZZ
: Projection
JPBIA6830ZZ
EM-170
< PERIODIC MAINTENANCE >
[QR25DE]
AIR CLEANER FILTER
• Check that pawls
and
(3 in total) of air duct 2
are engaged.
Inspection (Dry Paper Type)
INFOID:0000000010783773
INSPECTION AFTER REMOVAL
Examine with eyes that there is no stain, clogging, or damage on air cleaner element.
• Remove dusts (such as dead leafs) on air cleaner element surface and inside cleaner case.
• To clean air cleaner element
, blow air on it from the air intake manifold side
to remove trash or dust.
CAUTION:
• When blowing air on the air cleaner element, attach the
cover to the air cleaner case and stay away from the vehicle
as much as possible to prevent the entry of dirt into the air
cleaner case.
• Never blow air from the ambient air side to prevent clogging.
When the ambient air side needs to be cleaned, attach the
cover to the intake manifold side and lightly dust by hand.
• If clogging or damage is observed, replace the air cleaner element.
MAINTENANCE INTERVAL
MA-42, "AIR CLEANER FILTER : Inspection (Dry Paper Type)"
.
: Vehicle front
JPBIA6828ZZ
Ambient air side
Air blow direction
JSBIA3460ZZ
SPARK PLUG
EM-171
< PERIODIC MAINTENANCE >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SPARK PLUG
Exploded View
INFOID:0000000010783775
Removal and Installation
INFOID:0000000010783776
REMOVAL
1.
Remove air duct assembly. Refer to
.
2.
Remove ignition coil.
3.
Remove spark plug with spark plug wrench (commercial service
tool).
CAUTION:
• Never drop or shock spark plug.
• Never disassemble ignition coil.
INSTALLAITON
Install in the reverse order of removal.
Inspection
INFOID:0000000010783777
INSPECTION AFTER REMOVAL
Use standard type spark plug for normal condition.
Visually check the electrode for dirt and wear and the insulator for burning.
Ignition coil
Spark plug
Rocker cover
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSBIA3314ZZ
:
14 mm (0.55 in)
JPBIA0030ZZ
Spark plug (standard)
: Refer to
EM-172
< PERIODIC MAINTENANCE >
[QR25DE]
SPARK PLUG
CAUTION:
• Never drop or shock spark plug.
• Never use wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be
used.
• Checking and adjusting plug gap is not required between
change intervals.
Cleaner air pressure:
Less than 588 kPa (5.9 bar , 6 kg/
cm
2
, 85 psi)
Cleaning time:
Less than 20 seconds
SMA773C
JPBIA0031ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст