Nissan X-Trail 32. Manual — part 111
BR-38
< REMOVAL AND INSTALLATION >
[LHD]
BRAKE BOOSTER
CAUTION:
Never reuse brake fluid to drain.
• Check each item of brake pedal. Adjust it if the measurement value is not the standard. Refer to
.
Inspection and Adjustment
INFOID:0000000010838524
INSPECTION BEFORE REMOVAL
Air Tight
CAUTION:
Check the air tight condition when the master cylinder and the brake booster is installed.
1.
Check the air tight use a handy vacuum pump.
2.
If the air tight condition cannot be maintained, perform the following operation.
a.
Check the no dirt and dust are present on the brake booster and brake master cylinder mating faces.
Clean it if necessary.
b.
Check the O-ring on the master cylinder. If anything is found, replace the O-ring. Refer to
c.
Check the air tight condition again. If the condition still cannot be maintained, replace the brake booster.
INSPECTION AFTER REMOVAL
Check Valve Inspection
1.
Check the check valve to use a handy vacuum pump.
Input Rod Length rod Inspection
1.
Check the input length (A).
2.
Replace the brake booster if the input rod length is not the stan-
dard.
INSPECTION AFTER INSTALLATION
Operation
Depress the brake pedal several times at 5-second intervals with the engine stopped. Start the engine with the
brake pedal fully depressed. Check that the clearance between brake pedal and dash lower panel decreases.
NOTE:
A slight impact with a small click may be felt on the pedal when the brake pedal is fully depressed. this is nor-
mal phenomenon due to the brake system operation.
Air Tight
1.
Run the engine at idle for 1 minute to apply vacuum to the brake booster, and stop the engine.
At vacuum of
−
66.7 kPa (
−
500 mmHg,
−
19.69 inHg,
−
0.067 bar)
: Vacuum should decrease within 3.3 kPa (24.8 mmHg,
0.98 inHg, 0.033 bar) for 15 seconds.
In the case of connecting to brake
booster
: Vacuum should decrease within 3.3 kPa (24.8 mmHg,
0.98 inHg, 0.033 bar) for 15 seconds at vacuum of
−
66.7 kPa (
−
500 mmHg,
−
19.69 inHg,
−
0.067 bar).
In the case of connecting to vacuum
hose
: Vacuum should not exist.
:Input rod
A
: Refer to
.
JSFIA2251ZZ
BRAKE BOOSTER
BR-39
< REMOVAL AND INSTALLATION >
[LHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
2.
Depress the brake pedal several times at 5-second intervals until the accumulated vacuum is released to
atmospheric pressure. Check that the clearance between brake pedal and dash lower panel gradually
increases each time.
3.
Depress the brake pedal with the engine running. Then stop the engine while holding down the brake
pedal. Check that the brake pedal stroke does not change after holding down the brake pedal for 30 sec-
onds or more.
ADJUSTMENT AFTER INSTALLATION
Perform the brake pedal adjustment after installing the brake pedal assembly. Refer to
.
BR-40
< REMOVAL AND INSTALLATION >
[LHD]
VACUUM LINES
VACUUM LINES
MR20DD
MR20DD : Exploded View
INFOID:0000000010838525
MR20DD
MR20DD : Removal and Installation
INFOID:0000000010838526
REMOVAL
1.
Remove the vacuum hose and vacuum piping.
2.
Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, install the vacuum hose.
• When installing vacuum hose, insert it until its tip reaches the
back-end of length (A) or further as shown in the figure.
CAUTION:
Never use lubricating oil during assembly.
- Face the paint mark of vacuum hose (built-in check valve) to
upward to assemble.
- Face the paint mark of vacuum piping (intake manifold side) to
upward to assemble.
- Face the other paint marks to vehicle front side to assemble.
- For clamp mounting direction (the orientation of pawl), refer to
MR20DD : Inspection
INFOID:0000000010838527
INSPECTION AFTER REMOVAL
Appearance
Check for correct assembly, damage and deterioration.
QR25DE
Vacuum piping
Vacuum hose
Clamp
To intake manifold
Paint mark
To brake booster
JSFIA2423ZZ
A
: 24 mm (0.95 in) or more
JPFIA0023ZZ
VACUUM LINES
BR-41
< REMOVAL AND INSTALLATION >
[LHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
QR25DE : Exploded View
INFOID:0000000010838528
QR25DE
QR25DE : Removal and Installation
INFOID:0000000010838529
REMOVAL
1.
Remove the vacuum hose and vacuum piping.
2.
Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, install the vacuum hose.
• When installing vacuum hose, insert it until its tip reaches the
back-end of length (A) or further as shown in the figure.
CAUTION:
Never use lubricating oil during assembly.
- Face the paint mark of vacuum hose (built-in check valve) to
upward to assemble.
- Face the paint mark of vacuum piping (intake manifold side) to
upward to assemble.
- Face the other paint marks to vehicle front side to assemble.
- For clamp mounting direction (the orientation of pawl), refer to
QR25DE : Inspection
INFOID:0000000010838530
INSPECTION AFTER REMOVAL
Appearance
Check for correct assembly, damage and deterioration.
R9M
Vacuum piping
Vacuum hose
Clamp
To intake manifold
Paint mark
To brake booster
JSFIA2385ZZ
A
: 24 mm (0.95 in) or more
JPFIA0023ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст