Nissan X-Trail 32. Manual — part 1220
TAIL LAMP CIRCUIT
EXL-337
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Back door side
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK TAIL LAMP GROUND CIRCUIT
Check continuity between each tail lamp harness connector and ground.
Body side
Back door side
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TAIL LAMP BULB
Check the applicable tail lamp bulb.
Is the inspection result normal?
YES
>> Check the corresponding tail lamp bulb socket and harness. Repair or replace if necessary.
NO
>> Replace the corresponding tail lamp bulb. Refer to
EXL-389, "REAR COMBINATION LAMP
EXL-391, "REAR COMBINATION LAMP (BACK
(back door side).
IPDM E/R
Rear combination lamp (back door side)
Continuity
Connector
Terminal
Connector
Terminal
RH
E10
17
D156
1
Existed
LH
4
D155
Rear combination lamp (body side)
—
Continuity
Connector
Terminal
RH
B59
1
Ground
Existed
LH
B80
Rear combination lamp (back door side)
—
Continuity
Connector
Terminal
Terminal
RH
D156
1
Ground
Existed
LH
D155
EXL-338
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
LICENSE PLATE LAMP CIRCUIT
LICENSE PLATE LAMP CIRCUIT
Component Function Check
INFOID:0000000010789863
1.
CHECK TAIL LAMP LH OPERATION
Check that tail lamp LH is turned ON when lighting switch is turned 1ST.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check tail lamp circuit. Refer to
EXL-336, "Component Function Check"
.
2.
CHECK LICENSE PLATE LAMP OPERATION
With CONSULT
1.
Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.
2.
With operating the test items, check that the license plate lamp is turned ON.
Is the inspection result normal?
YES
>> License plate lamp circuit is normal.
NO
>> Refer to
EXL-338, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010789864
1.
CHECK LICENSE PLATE LAMP POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and license plate lamp connector.
3.
Check continuity between IPDM E/R harness connector and license plate lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK LICENSE PLATE LAMP GROUND CIRCUIT
Check continuity between license plate lamp harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK LICENSE PLATE LAMP BULB
Check the applicable license plate lamp bulb.
Is the inspection result normal?
YES
>> Check the corresponding license plate lamp bulb socket. Repair or replace if necessary.
NO
>> Replace the corresponding license plate lamp bulb. Refer to
.
On
: License plate lamp ON
Off
: License plate lamp OFF
IPDM E/R
License plate lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E10
4
D161
2
Existed
LH
D162
License plate lamp
—
Continuity
Connector
Terminal
RH
D161
1
Ground
Existed
LH
D162
DAYTIME RUNNING LIGHT CIRCUIT
EXL-339
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DAYTIME RUNNING LIGHT CIRCUIT
Component Function Check
INFOID:0000000010789865
1.
CHECK DAYTIME RUNNING LIGHT OPERATION
With CONSULT
1.
Select “DAYTIME RUNNING LIGHT” in “Active Test” mode of “IPDM E/R” using CONSULT.
2.
With operating the test items, check that the daytime running light is turned ON.
Is the inspection result normal?
YES
>> Daytime running light circuit is normal.
NO
>> Refer to
EXL-339, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010789866
1.
CHECK DAYTIME RUNNING LIGHT OUTPUT VOLTAGE
With CONSULT
1.
Turn ignition switch OFF.
2.
Disconnect front combination lamp connector.
3.
Turn ignition switch ON.
4.
Select “DAYTIME RUNNING LIGHT” in “Active Test” mode of “IPDM E/R” using CONSULT.
5.
With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace IPDM E/R. Refer to
PCS-60, "Removal and Installation"
.
2.
CHECK DAYTIME RUNNING LIGHT POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front combination lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DAYTIME RUNNING LIGHT GROUND CIRCUIT
Check continuity between front combination lamp harness connector and ground.
On
: Daytime running light ON
Off
: Daytime running light OFF
+
-
Test item
Voltage
IPDM E/R
Connector
Terminal
RH
E149
58
Ground
DAYTIME RUN-
NING LIGHT
On
9 – 16 V
Off
0 – 1 V
LH
E148
49
On
9 – 16 V
Off
0 – 1 V
IPDM E/R
Front combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E149
58
E151
1
Existed
LH
E148
49
E153
EXL-340
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
DAYTIME RUNNING LIGHT CIRCUIT
Is the inspection result normal?
YES
>> Replace the corresponding front combination lamp. Refer to
EXL-376, "Removal and Installation"
.
NO
>> Repair or replace harness.
Front combination lamp
—
Continuity
Connector
Terminal
RH
E151
2
Ground
Existed
LH
E153
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст