Nissan X-Trail 32. Manual — part 1941
SN-220
< DTC/CIRCUIT DIAGNOSIS >
[WITH PARK ASSIST]
B272E-12 SIDE SENSOR [FL]
Is the inspection result normal?
YES
>> Replace side sensor front LH. Refer to
SN-239, "FRONT : Removal and Installation"
NO
>> Repair or replace malfunctioning parts.
Terminals
Continuity
(+)
(
−
)
Side sensor front LH
Connector
Terminal
E171
2
Ground
Not existed
SN
B272E-14 SIDE SENSOR [FL]
SN-221
< DTC/CIRCUIT DIAGNOSIS >
[WITH PARK ASSIST]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B272E-14 SIDE SENSOR [FL]
DTC Description
INFOID:0000000010776922
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors (side sensor front LH circuit)
• Side sensor front LH
FAIL-SAFE
• Obstacle detection function is stopped
• Alarm display is displayed on the information display of combination meter
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.
5.
Check DTC.
Is DTC B272E-14 detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010776923
1.
CHECK SIDE SENSOR SIGNAL FRONT LH CIRCUIT FOR OPEN
1.
Turn ignition switch OFF.
2.
Disconnect sonar control unit harness connector and side sensor front LH harness connector.
3.
Check the continuity between sonar control unit harness connector and side sensor front LH harness con-
nector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK SIDE SENSOR SIGNAL FRONT LH CIRCUIT FOR SHORT
Check the continuity between sonar control unit harness connector and ground.
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B272E-14
SIDE SENSOR [FL]
(Side sensor front-left)
OPEN/SHORT-
GND
(Open/Short to
ground)
Short circuit to ground or open circuit is detected in harness be-
tween sonar control unit and side sensor front LH when ignition
switch is turned ON.
Sonar control unit
Side sensor front LH
Continuity
Connector
Terminal
Connector
Terminal
B128
28
E171
2
Existed
SN-222
< DTC/CIRCUIT DIAGNOSIS >
[WITH PARK ASSIST]
B272E-14 SIDE SENSOR [FL]
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK FRONT SENSOR GROUND CIRCUIT
Check the continuity between sonar control unit harness connector and side sensor front LH harness connec-
tor.
Is the inspection result normal?
YES
>> Replace side sensor front LH. Refer to
SN-239, "FRONT : Removal and Installation"
NO
>> Repair or replace malfunctioning parts.
Terminals
Continuity
(+)
(
−
)
Sonar control unit
Connector
Terminal
B128
28
Ground
Not existed
Sonar control unit
Side sensor front LH
Continuity
Connector
Terminal
Connector
Terminal
B128
36
E171
3
Existed
SN
B272E-55 SIDE SENSOR [FL]
SN-223
< DTC/CIRCUIT DIAGNOSIS >
[WITH PARK ASSIST]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B272E-55 SIDE SENSOR [FL]
DTC Description
INFOID:0000000010776924
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Side sensor front LH
• Control unit setting of sonar control unit is incomplete
FAIL-SAFE
• Obstacle detection function is stopped
• Alarm display is displayed on the information display of combination meter
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.
5.
Check DTC.
Is DTC B272E-55 detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010776925
1.
PERFORM CONFIGURATION OF SONAR CONTROL UNIT
Perform configuration of sonar control unit. Refer to
SN-156, "CONFIGURATION (SONAR CONTROL UNIT) :
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Perform DTC confirmation procedure again. Refer to
Is DTC B272E-55 detected again?
YES
>> Replace side sensor front LH. Refer to
SN-239, "FRONT : Removal and Installation"
NO
>> INSPECTION END.
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B272E-55
SIDE SENSOR [FL]
(Side sensor front-left)
CONFIG ERROR
(Configuration er-
ror)
Control unit setting of sonar control unit is incomplete or is not set
normally.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст