Nissan X-Trail 32. Manual — part 1471
BODY SIDE TRIM
INT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
CAUTION:
Never apply excessive force when removing center pillar upper garnish. Otherwise, pawl may be
damaged and fragments may drop in panel holes on the body panel.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace center pillar upper garnish with a new part after removal. Never reuse center pillar upper
garnish.
• Check in advance that pawls are accurately aligned with the portions on the body panel, and then
install by pressing in.
• Tighten seat belt shoulder anchor mounting anchor bolt to the specified torque. Refer to
.
PIIB7674J
INT-30
< REMOVAL AND INSTALLATION >
FLOOR TRIM
FLOOR TRIM
Exploded View
INFOID:0000000010730556
FRONT FLOOR CARPET
FRONT FLOOR CARPET : Removal and Installation
INFOID:0000000010730557
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the body panel.
REMOVAL
1.
Remove front seat assembly (LH and RH). Refer to
SE-41, "Removal and Installation"
2.
Remove second seat cushion. Refer to
SE-54, "Removal and Installation"
.
Rear floor carpet
Front floor carpet
Carpet hook
Harness clip
Rear floor spacer RH
Front floor spacer RH
Front floor spacer LH
Rear floor spacer LH
Steering column hole cover
: Clip
: Always replace after every disassembly.
JMJIB0198ZZ
FLOOR TRIM
INT-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3.
Remove dash side finisher (LH and RH). Refer to
INT-26, "DASH SIDE FINISHER : Removal and Installa-
4.
Remove center pillar lower garnish (LH and RH). Refer to
INT-27, "CENTER PILLAR LOWER GARNISH :
.
5.
Remove center console assembly. Refer to the following.
• LHD models: Refer to
IP-25, "Removal and Installation"
.
• RHD models: Refer to
IP-52, "Removal and Installation"
.
6.
Remove shift selector assembly. Refer to the following.
• 6MT models (RS6F94R): Refer to
TM-28, "Removal and Installation"
• 6MT models (RS6F52A): Refer to
TM-106, "Removal and Installation"
• CVT models (RE0F10D): Refer to
TM-403, "Removal and Installation"
.
• CVT models (RE0F10G): Refer to
TM-667, "Removal and Installation"
.
7.
Remove diagnosis sensor unit. Refer to
SR-38, "Removal and Installation"
.
8.
Disengage parking brake harness connector
.
9.
Disengage harness clips.
10. Remove rear floor duct 1. Refer to
VTL-13, "REAR FLOOR DUCT 1 : Removal and Installation"
11. Remove drain hose from A/C unit assembly.
12. Remove instrument stay mounting nuts
, and then remove instrument stay LH
and instrument stay
RH .
: Vehicle front
JMJIB0203ZZ
JMJIA9632ZZ
JMJIB0202ZZ
INT-32
< REMOVAL AND INSTALLATION >
FLOOR TRIM
13. Remove steering column hole cover fixing clips
, and then
remove steering column hole cover.
14. Disengage carpet hook fixing clip using a remover tool (A)
according to numerical order 1
→
2 indicated by the arrows as
shown in the figure.
15. Peel off magic fasteners
of front floor carpet front end.
16. Peel off magic fasteners
of front floor carpet rear end.
17. Remove floor carpet
from harness clips
.
JMJIB0196ZZ
: Clip
JMJIA6083ZZ
: Vehicle front
JMJIB0197ZZ
: Vehicle front
JMJIA9634ZZ
JMJIA9635ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст