Nissan X-Trail 32. Manual — part 1131
SERVICE DATA AND SPECIFICATIONS (SDS)
EM-421
< SERVICE DATA AND SPECIFICATIONS (SDS)
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Main Bearing
INFOID:0000000010784377
MAIN BEARING GRADE TABLE
MAIN BEARING OIL CLEARANCE
Unit: mm (in)
Connecting Rod Bearing
INFOID:0000000010784378
CONNECTING ROD BEARING OIL CLEARANCE
Unit: mm (in)
Cylinder block main bearing
housing inner diameter
Grade mark A
55.4975 - 55.4985 (2.1849 - 2.185)
Grade mark B
55.4985 - 55.4995 (2.185)
Grade mark C
55.4995 - 55.5005 (2.185 - 2.1851)
Grade mark E
55.5005 - 55.5015 (2.1851)
Grade mark H
55.5015 - 55.5025 (2.1851)
Grade mark J
55.5025 - 55.5035 (2.1851 - 2.1852)
Grade mark K
55.5035 - 55.5045 (2.1852)
Grade mark L
55.5045 - 55.5055 (2.1852 - 2.1853)
Grade mark M
55.5055 - 55.5065 (2.1853)
Grade mark P
55.5065 - 55.5075 (2.1853)
Grade mark S
55.5075 - 55.5085 (2.1853 - 2.1854)
Grade mark T
55.5085 - 55.5095 (2.1854)
Grade mark U
55.5095 - 55.5105 (2.1854)
Grade mark Z
55.5105 - 55.5115 (2.1854 - 2.1855)
Marking
Thickness Identification
color
Lower shell
bearing
33281R or 4
1.989 mm (0.0783 in)
Blue
38751R or 3
1.985 mm (0.0781 in)
Black
37686R or 2
1.981 mm (0.0780 in)
Yellow
31153R or 1
1.977 mm (0.0778 in)
White
Upper shell
bearing
53785R or 4
1.989 mm (0.0783 in)
Blue
54889 or 3
1.985 mm (0.0781 in)
Black
7527 (upper)
1.981 mm (0.0780 in)
Yellow
7521 (lower)
1.977 mm (0.0778 in)
White
Main bearing oil clearance
Standard
0.035 - 0.065 (0.0014 - 0.0026)
Connecting rod bearing oil clearance
Standard
0.053 - 0.093 (0.0021 - 0.0037)
EX-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
EX
A
EX
N
O
P
CONTENTS
EXHAUST SYSTEM
MR20DD
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
PERIODIC MAINTENANCE . . . . . . ..
EXHAUST SYSTEM . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
EXHAUST SYSTEM . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
QR25DE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . .
Special Service Tools . . . . . . . . . . . ..
Commercial Service Tools . . . . . . . . . ...
PERIODIC MAINTENANCE . . . . . .
EXHAUST SYSTEM . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
EXHAUST SYSTEM . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
R9M
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Precautions for Removing Battery Terminal . . .
PERIODIC MAINTENANCE . . . . . .
EXHAUST SYSTEM . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
EXHAUST SYSTEM . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
EX-2
< PRECAUTION >
[MR20DD]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Removal and Installation
INFOID:0000000010782879
CAUTION:
• Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat
resistance, corrosion resistance, and shape.
• Perform the operation with the exhaust system fully cooled down because the system will be hot
just after engine stops.
• Be careful not to cut your hand on the heat insulator edge.
• Never use silicon-containing products (e.g. oil) to prevent malfunctions such as the interference with
the conduction of electricity and the occurrence of noise in the radio.
• Prevent rust preventives from adhering to the sensor body.
Precautions for Removing Battery Terminal
INFOID:0000000010782919
• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the intelligent key
or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even
after the ignition switch is turned to the OFF position, i.e. ACC power is supplied for a certain fixed time.
• When disconnecting the 12V battery terminal, turn off the ACC
power before disconnecting the 12V battery terminal, observing
“How to disconnect 12V battery terminal” described below.
NOTE:
Some ECUs operate for a certain fixed time even after ignition
switch is turned OFF and ignition power supply is stopped. If the
battery terminal is disconnected before ECU stops, accidental DTC
detection or ECU data damage may occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to Instruction 1 or Instruction 2 described below.
For vehicles parked by ignition switch OFF, refer to Instruction 2.
INSTRUCTION 1
1.
Open the hood.
2.
Turn key switch to the OFF position with the driver side door opened.
3.
Get out of the vehicle and close the driver side door.
4.
Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
5.
Remove 12V battery terminal.
SEF289H
D4D engine
: 20 minutes
HRA2DDT
: 12 minutes
K9K engine
: 4 minutes
M9R engine
: 4 minutes
R9M engine
: 4 minutes
V9X engine
: 4 minutes
PRECAUTIONS
EX-3
< PRECAUTION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
INSTRUCTION 2 (FOR VEHICLES PARKED BY IGNITION SWITCH OFF)
1.
Unlock the door with intelligent key or remote keyless entry.
NOTE:
At this moment, ACC power is supplied.
2.
Open the driver side door.
3.
Open the hood.
4.
Close the driver side door.
5.
Wait at least 3 minutes.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст