Nissan Terrano r20e. Manual — part 20
DIAGNOSTIC PROCEDURE
CHECK TCM POWER SOURCE.
1. Turn ignition switch to “ON” position.
(Do not start engine.)
2. Check voltage between TCM terminals
q
42
,
q
47
and ground.
Battery voltage should exist.
OK
E
NG
Check the following items:
I
Harness for short or
open between ignition
switch and TCM (Main
harness)
I
Ignition switch and fuse
Refer to EL section
(“POWER SUPPLY
ROUTING”).
CHECK A/T FLUID TEMPERATURE
SENSOR WITH TERMINAL CORD
ASSEMBLY.
1. Turn ignition switch to “OFF” position.
2. Disconnect terminal cord assembly
connector in engine compartment.
3. Check resistance between terminals
q
6
and
q
7
when A/T is cold.
Resistance:
Cold [20°C (68°F)]
Approximately 2.5 k
Ω
4. Reinstall any part removed.
OK
E
NG
1. Remove oil pan.
2. Check the following
items:
I
A/T fluid temperature
sensor
Refer to “COMPONENT
INSPECTION” on next
page.
I
Harness of terminal cord
assembly for short or
open
q
A
(Go to next page.)
YAT316
YAT317
H
H
TROUBLE DIAGNOSIS FOR BATT/FLUID TEMP SEN
A/T Fluid Temperature Sensor and TCM Power
Source (Cont’d)
AT-77
q
A
CHECK INPUT SIGNAL OF A/T FLUID
TEMPERATURE SENSOR.
1. Start engine.
2. Select “ECU INPUT SIGNALS” in
Data Monitor.
3. Read out the value of “FLUID
TEMP SE”.
Voltage:
Cold [20°C (68°F)]
→
Hot [80°C (176°F)]:
Approximately
1.5V
→
0.5V
----------------------------------------------------------------------------------------------------------------------- OR -----------------------------------------------------------------------------------------------------------------------
1. Start engine.
2. Check voltage between TCM ter-
minal
q
47
and ground while warm-
ing up A/T.
Voltage:
Cold [20°C (68°F)]
→
Hot [80°C (176°F)]:
Approximately
1.5V
→
0.5V
OK
E
NG
Check the following item:
I
Harness for short or
open between TCM and
terminal cord assembly
(Main harness)
Perform “SELF-DIAGNOSIS CODE CON-
FIRMATION PROCEDURE”, AT-76.
OK
E
NG
1. Perform TCM input/
output signal inspection.
2. If NG, recheck TCM pin
terminals for damage or
loose connection with
harness connector.
INSPECTION END
COMPONENT INSPECTION
A/T fluid temperature sensor
I
For removal, refer to AT-113.
I
Check resistance between terminals
q
6
and
q
7
while changing
temperature as shown at left.
Temperature °C (°F)
Resistance
20 (68)
Approximately 2.5 k
Ω
80 (176)
Approximately 0.3 k
Ω
YAT318
YAT319
H
H
H
TROUBLE DIAGNOSIS FOR BATT/FLUID TEMP SEN
A/T Fluid Temperature Sensor and TCM Power
Source (Cont’d)
AT-78
Wiring Diagram — AT — ENGSS
YAT271
TROUBLE DIAGNOSIS FOR ENGINE SPEED SIG
AT-79
Engine Speed Signal
DESCRIPTION
The engine speed signal is sent from the ECM to the TCM.
ON BOARD DIAGNOSIS LOGIC
Diagnostic trouble code
Malfunction is detected when ...
Check items
(Possible cause)
:
ENGINE SPEED SIG
TCM does not receive the proper volt-
age signal from ECM.
I
Harness or connectors
(The sensor circuit is open or
shorted.)
:
9th judgement flicker
SELF-DIAGNOSIS CODE CONFIRMATION PROCEDURE
After the repair, perform the following procedure to confirm the
malfunction is eliminated.
1)
Start engine.
2)
Select “SELF-DIAG RESULTS” mode with CONSULT-II.
3)
Drive vehicle under the following conditions:
Selector lever in “D” position, vehicle speed higher than
10 km/h (6 MPH), throttle opening greater than 1/8 of the
full throttle position and driving for more than 10 sec-
onds.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ OR ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1)
Start engine.
2)
Drive vehicle under the following conditions:
Selector lever in “D” position, vehicle speed higher than
10 km/h (6 MPH), throttle opening greater than 1/8 of the
full throttle position and driving for more than 10 sec-
onds.
3)
Perform self-diagnosis.
Refer to SELF-DIAGNOSTIC PROCEDURE (Without
CONSULT-II), AT-15.
SAT823H
TROUBLE DIAGNOSIS FOR ENGINE SPEED SIG
AT-80
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст