Nissan Terrano r20e. Manual — part 49

10. Install oil pan.
a. Attach a magnet to oil pan.

b. Install new oil pan gasket on transmission case.
c. Install oil pan and bracket on transmission case.

I

Always replace oil pan bolts as they are self-sealing bolts.

I

Before installing bolts, remove traces of sealant and oil
from mating surface and thread holes.

I

Tighten four bolts in a criss-cross pattern to prevent dis-
location of gasket.

d. Tighten drain plug.

11. Install park/neutral position switch.
a. Check that manual shaft is in “1” position.
b. Temporarily install park/neutral position switch on manual shaft.
c. Move manual shaft to “N”.

d. Tighten bolts while inserting 4.0 mm (0.157 in) dia. pin vertically

into locating holes in park/neutral position switch and manual
shaft.

12. Install torque converter.
a. Pour ATF into torque converter.

I

Approximately 2 liters (1-3/4 Imp qt) of fluid are required for
a new torque converter.

I

When reusing old torque converter, add the same amount
of fluid as was drained.

SAT011B

NAT291

NAT292

NAT290

SAT428DA

ASSEMBLY

Assembly (2) (Cont’d)

AT-193

b. Install torque converter while aligning notches and oil pump.

c. Measure distance A to check that torque converter is in proper

position.

Distance “A”:

26.0 mm (1.024 in) or more

SAT016B

SAT017B

ASSEMBLY

Assembly (2) (Cont’d)

AT-194

A/T Fluid Cooler

REMOVAL AND INSTALLATION

1. Remove front radiator grill. Refer to BT section (“BODY END”).
2. Disconnect fluid hoses from fluid cooler unit.
3. Remove fluid cooler unit.
4. Remove fluid cooler bracket.
5. Remove clips securing fluid hose (cooler unit to radiator) and

loosen hose clamps, then remove the fluid hose.

6. Loosen clamps securing fluid hose (A/T assembly to fluid

cooler), then remove the fluid hose.

7. Remove bolts securing fluid cooler tube bracket.
8. Remove fluid hose with bracket.

Reverse the removal procedure to install the A/T fluid cooler
unit. Refer to the component drawing and specified tightening
torque.
Check A/T fluid level and refill if necessary. Refer to MA sec-
tion (“CHASSIS AND BODY MAINTENANCE”).

NAT288

NAT289

A/T FLUID COOLER SYSTEM

AT-195

General Specifications

Applied model

TD27ETi engine

Automatic transmission model

RE4R01A

Transmission model code number

4GX07

Stall torque ratio

2.0 : 1

Transmission gear ratio

1st

2.785

2nd

1.545

Top

1.000

OD

0.694

Reverse

2.272

Recommended fluid

Genuine Nissan ATF or equiva-

lent*1

Fluid capacity



(Imp qt)

8.5 (7-1/2)

*1: Refer to MA section (“Fluids and Lubricants”, “RECOMMENDED

FLUIDS AND LUBRICANTS”).

Specifications and Adjustment

SHIFT SCHEDULE

Vehicle speed when shifting gears

Throttle position

Vehicle speed km/h (MPH)

D

1

,

D

2

D

2

,

D

3

D

3

,

D

4

D

4

,

D

3

D

3

,

D

2

D

2

,

D

1

1

2

,

1

1

Full throttle

32 - 36

(20 - 23)

66 - 74

(41 - 46)

108 - 118

(68 - 74)

103 - 113

(64 - 71)

61 - 69

(38 - 43)

27 - 31

(17 - 19)

43 - 47

(27 - 29)

Half throttle

30 - 34

(19 - 21)

62 - 68

(39 - 43)

82 - 92

(51 - 58)

67 - 75

(42 - 47)

26 - 32

(16 - 20)

7 - 11

(4 - 7)

43 - 47

(27 - 29)

Vehicle speed when performing and
releasing lock-up

Throttle
position

Overdrive con-

trol switch

[Shift position]

Vehicle speed km/h (MPH)

Lock-up

“ON”

Lock-up

“OFF”

Full throttle

ON

[D

4

]

121 - 129

(76 - 81)

116 - 124

(73 - 78)

OFF

[D

3

]

74 - 82

(46 - 51)

74 - 82

(46 - 51)

Half throttle

ON

[D

4

]

104 - 112

(65 - 70)

93 - 101

(58 - 63)

OFF

[D

3

]

74 - 82

(46 - 51)

74 - 82

(46 - 51)

STALL REVOLUTION

Stall revolution

rpm

2,450 - 2,700

LINE PRESSURE

Engine speed

rpm

Line pressure kPa (bar, kg/cm

2

, psi)

D, 2 and 1 positions

R position

Idle

422 - 461

(4.22 - 4.61,

4.3 - 4.7,

61 - 67)

589 - 627

(5.89 - 6.27,

6.01 - 6.40,
85.4 - 90.9)

Stall

1,020 - 1,098

(10.20 - 10.98,

10.4 - 11.2,

148 - 159)

1,422 - 1,500

(14.22 - 15.00,

14.5 - 15.3,

206 - 218)

SERVICE DATA AND SPECIFICATIONS (SDS)

AT-196