Nissan Terrano r20e. Manual — part 388
*: Special tool or commercial equivalent
Tool number
Tool name
Description
Unit application
R180A
H233B
ST33190000*
Diff. side bearing drift
Installing side bearing inner cone
A: 52 mm (2.05 in) dia.
B: 34 mm (1.34 in) dia.
—
X
ST33081000*
Side bearing puller
adapter
Installing side bearing inner cone
A: 43 mm (1.69 in) dia.
B: 33.5 mm (1.319 in) dia.
—
X
ST30611000*
Drift
Installing pinion rear bearing outer race
X
X
ST30621000*
Drift
Installing pinion rear bearing outer race
A: 79 mm (3.11 in) dia.
B: 59 mm (2.32 in) dia.
X
X
ST30701000*
Drift
Installing pinion front bearing outer race
A: 61.5 mm (2.421 in) dia.
B: 41 mm (1.61 in) dia.
X
—
ST30613000*
Drift
Installing pinion front bearing outer race
A: 71.5 mm (2.815 in) dia.
B: 47.5 mm (1.870 in) dia.
—
X
KV381025S0*
Oil seal fitting tool
q
1
ST30720000
Drift bar
q
2
KV38102510
Drift
Installing front oil seal
A: 77 mm (3.03 in) dia.
B: 55 mm (2.17 in) dia.
C: 71 mm (2.80 in) dia.
D: 65 mm (2.56 in) dia.
X
X
ST33720000
Diff. side retainer
guide
Installing side retainer
X
—
ST33270000
Side oil seal drift
Installing side oil seal
A: 62 mm (2.44 in) dia.
B: 28 mm (1.10 in) dia.
X
—
PREPARATION
PD-4
Front propeller shaft (Model 0F71H)
Rear propeller shaft (Model 2S80B)
SPD724
SPD725
PROPELLER SHAFT
PD-5
On-Vehicle Service
PROPELLER SHAFT VIBRATION
If vibration is present at high speed, inspect propeller shaft runout
first.
1. Raise rear wheels.
2. Measure propeller shaft runout at points indicated below by
rotating final drive companion flange by hand.
Front propeller shaft
Unit: mm (in)
Propeller shaft model
0F71H
Measuring point A
126 (4.96)
Rear propeller shaft
Unit: mm (in)
Propeller shaft model
2S80B
H233B
Measuring point
A
280 (11.02)
B
475 (18.70)
C
280 (11.02)
3. If runout exceeds specifications, disconnect propeller shaft at
final drive companion flange; then rotate companion flange 180
degrees and reconnect propeller shaft.
Runout limit: 0.6 mm (0.024 in)
4. Check runout again. If runout still exceeds specifications,
replace propeller shaft assembly.
5. Perform road test.
APPEARANCE CHECKING
I
Inspect propeller shaft tube surface for dents or cracks. If
damaged, replace shaft assembly.
I
If center is noisy or damaged, replace center bearing.
SPD728
YPD005
NPD001
SPD102
PROPELLER SHAFT
PD-6
Removal and Installation
I
Put match marks on flanges and separate propeller shaft from
final drive.
I
Draw out propeller shaft from transmission and plug up rear
end of transmission rear extension housing.
Inspection
I
Inspect propeller shaft runout. If runout exceeds specifications,
replace propeller shaft assembly.
Runout limit:
0.6 mm (0.024 in)
I
Inspect journal axial play. If the play exceeds specifications,
replace propeller shaft assembly.
Journal axial play:
0.2 mm (0.008 in) or less
Disassembly
JOURNAL
1. Put match marks on shaft and flange or yoke.
SPD103
SPD359
SPD106
SPD165
SPD128
PROPELLER SHAFT
PD-7
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст