Nissan Terrano r20e. Manual — part 95
System Diagram
SEC390D
ENGINE AND EMISSION CONTROL OVERALL SYSTEM
ZD30DDTi
EC-17
Vacuum Hose Drawing
1.
Swirl control valve control solenoid
valve to swirl control valve actua-
tor
2.
Intake air control valve control
solenoid valve to intake air control
valve actuator
3.
Variable nozzle turbocharger con-
trol actuator to vacuum damper
4.
Variable nozzle turbocharger con-
trol solenoid valve to resonator
5.
Variable nozzle turbocharger con-
trol solenoid valve to vacuum
pump
Refer to “System Diagram”, EC-17 for vacuum control system.
MEC030E
ENGINE AND EMISSION CONTROL OVERALL SYSTEM
ZD30DDTi
EC-18
System Chart
Input (Sensor)
ECM Function
Output (Actuator)
I
Electronic control fuel injection pump
I
Crankshaft position sensor (TDC)
I
Engine coolant temperature sensor
I
Accelerator position sensor
I
Accelerator position switch
I
Accelerator switch (F/C)
I
Park/Neutral position (PNP) switch
I
Ignition switch
I
Battery voltage
I
Vehicle speed sensor
I
Air conditioner switch
I
Mass air flow sensor
I
Stop lamp switch
I
Heat up switch
I
Charge air pressure sensor*1
Fuel injection control
Electronic control fuel injection pump
Fuel injection timing control
Electronic control fuel injection pump
Fuel cut control
Electronic control fuel injection pump
Glow control system
Glow relay & glow lamp
On board diagnostic system
MIL (On the instrument panel)
EGR volume control
EGR volume control valve
Cooling fan control
Cooling fan relay
Air conditioning cut control
Air conditioner relay
Variable nozzle turbocharger control
Variable nozzle turbocharger control sole-
noid valve
Swirl control valve control
Swirl control valve control solenoid valve
Intake air control valve control
Intake air control valve control solenoid
valve
*1: This sensor is not used to control the engine system under normal conditions.
ENGINE AND EMISSION CONTROL OVERALL SYSTEM
ZD30DDTi
EC-19
Fuel Injection Control System
DESCRIPTION
System description
Three types of fuel injection control are provided to accommodate engine operating conditions; normal control,
idle control and start control. The ECM determines the appropriate fuel injection control. Under each control,
the amount of fuel injected is compensated to improve engine performance.
Pulse signals are exchanged between ECM and electronic control fuel injection pump (control unit is built-in).
The fuel injection pump control unit performs duty control on the spill valve (built into the fuel injection pump)
according to the input signals to compensate the amount of fuel injected to the preset value.
Start control
Input/output signal chart
Sensor
Input Signal to ECM
ECM Function
Actuator
Engine coolant temperature sensor
Engine coolant temperature
Fuel injection con-
trol (start control)
Electronic control fuel injec-
tion pump
Crankshaft position sensor (TDC)
Engine speed
Ignition switch
Start signal
When the ECM receives a start signal from the ignition switch, the
ECM adapts the fuel injection system for the start control. The
amount of fuel injected at engine starting is a preset program value
in the ECM. The program is determined by the engine speed and
engine coolant temperature.
For better startability under cool engine conditions, the lower the
coolant temperature becomes, the greater the amount of fuel
injected. The ECM ends the start control when the engine speed
reaches the specific value, and shifts the control to the normal or
idle control.
Idle control
Input/output signal chart
Sensor
Input Signal to ECM
ECM Function
Actuator
Engine coolant temperature sensor
Engine coolant temperature
Fuel injection con-
trol (Idle control)
Electronic control fuel injec-
tion pump
Crankshaft position sensor (TDC)
Engine speed
Park/Neutral position (PNP) switch
Gear position
Battery
Battery voltage
Accelerator position switch
Idle position
Vehicle speed sensor
Vehicle speed
Air conditioner switch
Air conditioner signal
Heat up switch
Heat up switch signal
When the ECM determines that the engine speed is at idle, the fuel injection system is adapted for the idle
control. The ECM regulates the amount of fuel injected corresponding to changes in load applied to the engine
to keep engine speed constant. The ECM also provides the system with a fast idle control in response to the
engine coolant temperature and heat up switch signal.
SEF648S
ENGINE AND EMISSION BASIC CONTROL SYSTEM
DESCRIPTION
ZD30DDTi
EC-20
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст