Nissan Titan. Manual — part 12
BR-38
< REMOVAL AND INSTALLATION >
REAR DISC BRAKE
3. Install cylinder body (2) and tighten sliding pin bolts (1) to speci-
fication.
CAUTION:
Before installing cylinder body to the vehicle, wipe off
mounting surface of cylinder body.
4. Install brake hose connection (A) and new copper sealing
washer to cylinder body and tighten to specification.
CAUTION:
• Do not reuse copper sealing washer.
• Securely attach brake hose to protrusion on cylinder
body.
5. Install brake hose to brake piping. Refer to
BR-22, "Removal and Installation of Rear Brake Piping and
6. Refill with new brake fluid and bleed air. Refer to
BR-16, "Bleeding Brake System"
7. Check rear disc brake for drag and correct as necessary.
8. Install rear wheels and tires. Refer to
.
ALFIA0153ZZ
ALFIA0152ZZ
BRAKE MASTER CYLINDER
BR-39
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
BRAKE MASTER CYLINDER
Disassembly and Assembly
INFOID:0000000009883561
DISASSEMBLY
CAUTION:
• Master cylinder assembly cannot be disassembled.
• Do not drop parts. If a part is dropped, do not use it.
1. Pull the reservoir tank off the master cylinder assembly.
2. Remove the grommets from master cylinder assembly and discard the grommets.
CAUTION:
Discard the grommets, do not reuse.
3. Remove the fluid level sensor from the reservoir tank.
4. Remove the front and rear pressure sensors and discard.
CAUTION:
Discard the front and rear pressure sensors, do not reuse.
ASSEMBLY
CAUTION:
• Never use mineral oil such as kerosene, gasoline during the cleaning and assembly process.
• Do not drop parts. If a part is dropped, do not use it.
1.
Reservoir cap
2.
Fluid level sensor
3.
Grommet
4.
Master cylinder assembly
5.
Rear pressure sensor
6.
Front pressure sensor
7.
Seal
8.
Reservoir tank
B: Brake fluid
R: Rubber grease
AWFIA0961ZZ
BR-40
< UNIT DISASSEMBLY AND ASSEMBLY >
BRAKE MASTER CYLINDER
1. Apply brake fluid or rubber grease to the new grommets, then insert the new grommets into the master
cylinder assembly.
CAUTION:
Do not reuse the grommets.
2. Install the reservoir tank onto the master cylinder assembly.
3. Install the fluid level sensor on the reservoir tank.
4. Install the new front and rear pressure sensors.
CAUTION:
Do not reuse the front and rear pressure sensors.
FRONT DISC BRAKE
BR-41
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
FRONT DISC BRAKE
Disassembly and Assembly
INFOID:0000000009883562
DISASSEMBLY
1. Remove sliding pin bolt, and then remove the pad, shim, shim cover, and pad retainer from the torque
member.
2. Remove sliding pins and sliding pin boots from torque member.
3. Place a wooden block as shown, and blow air from union bolt
hole to remove pistons and piston boots.
WARNING:
Do not get your fingers caught between piston and wooden
block.
1.
Sliding pin bolt
2.
Bleed valve
3.
Cap
4.
Union bolt
5.
Brake hose
6.
Copper sealing washer
7.
Torque member bolt
8.
Sliding pin boot
9.
Torque member
10. Washers
11. Bushing
12. Sliding pin
13. Piston boot
14. Piston
15. Piston seal
16. Cylinder body
B.
Brake fluid
R.
Rubber grease
AWFIA0833GB
BRB0032D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст