Nissan Titan. Manual — part 647
ASSEMBLY
TM-271
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
23. Install needle bearing to transmission case.
CAUTION:
• Take care with the direction of needle bearing. Refer to
TM-226, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
24. Install output speed sensor (1) to transmission case and tighten
bolt (
) to specified torque.
CAUTION:
• Do not subject sensor to impact by dropping or hitting it.
• Do not disassemble sensor.
• Do not allow metal filings or any foreign material to get on
the sensor's front edge magnetic area.
• Do not place sensor in an area affected by magnetism.
25. As shown in the figure, use the drift to drive rear oil seal into the
rear extension (2WD models) (A) or adapter case (4WD models)
(B) until it is flush.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
26. Install return spring (1) to parking pawl (2).
SCIA5031E
Output speed sensor bolt : 5.8 N·m (0.59 kg-m, 51 in-lb)
JSDIA1321ZZ
1
: Drift [ST33400001 (J-26082)]
2
: Drift [Commercial service tool Ø64 mm (2.52 in)]
JSDIA1914ZZ
SCIA6180J
TM-272
< UNIT DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
27. Install parking pawl (with return spring) and pawl shaft to rear
extension (2WD models) or adapter case (4WD models).
28. Install parking actuator support to rear extension (2WD models)
or adapter case (4WD models).
29. Install needle bearing (1) to rear extension (2WD models) or
adapter case (4WD models).
CAUTION:
Apply petroleum jelly to needle bearing.
30. Install seal rings to output shaft.
CAUTION:
• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.
31. Install parking gear to output shaft.
SCIA3424E
SCIA3423E
SCIA6179J
SCIA5209E
SCIA5247E
ASSEMBLY
TM-273
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
32. Install output shaft in transmission case.
CAUTION:
Do not mistake front of shaft for rear because both sides
look similar (thinner end is front side).
33. Install bearing race to output shaft.
34. Install rear extension assembly (2WD models) or adapter case assembly (4WD models) according to the
following procedures.
a. 2WD models
i.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-21, "Recommended Chemical Prod-
.) to rear extension assembly as shown.
CAUTION:
Completely remove all moisture, oil, old sealant and any
foreign material from the transmission case and rear exten-
sion assembly mating surfaces.
ii.
Install rear extension assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
SCIA5030E
SCIA5245E
SCIA5212E
SCIA5029E
TM-274
< UNIT DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
iii. Tighten rear extension assembly bolts (
) to specified torque.
• Brackets (1)
• Self-sealing bolts (2)
CAUTION:
Do not reuse self-sealing bolt.
b. 4WD models
i.
Install gasket onto transmission case.
CAUTION:
• Completely remove all moisture, oil, old gasket and any
foreign material from the transmission case and adapter
case assembly mating surfaces.
• Do not reuse gasket.
ii.
Install adapter case assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
iii. Tighten adapter case assembly bolts (
) to specified torque.
• Brackets (1)
• Self-sealing bolts (2)
CAUTION:
Do not reuse self-sealing bolt.
Rear extension
assembly bolt
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt
: 61 N·m (6.2 kg-m, 45 ft-lb)
WCIA0562E
SCIA5231E
SCIA5186E
Adapter case
assembly bolt
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt : 61 N·m (6.2 kg-m, 45 ft-lb)
WCIA0563E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст