Nissan Titan. Manual — part 570
ST-16
< UNIT REMOVAL AND INSTALLATION >
POWER STEERING GEAR AND LINKAGE
9. Remove lower joint bolt on lower shaft.
10. Remove steering gear assembly bolts and nuts using power
tool, and then remove steering gear assembly from vehicle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse O-ring.
• After removing/installing or replacing steering components, check wheel alignment. Refer to
.
• After adjusting wheel alignment, adjust neutral position of steering angle sensor. Refer to
MENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
• With steering wheel in straight ahead position, make sure slit of
lower joint (A) fits with the projection on rear cover cap (B), while
checking that mark on steering gear assembly aligns with mark on
rear cover cap.
• After installation, bleed the air from the steering hydraulic system. Refer to
BR-16, "Bleeding Brake System"
.
INSPECTION AFTER INSTALLATION
Check if steering wheel turns smoothly when it is turned several times fully to the left and right lock positions.
LGIA0029E
LGIA0024E
SST491C
STEERING COLUMN
ST-17
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING COLUMN
Removal and Installation
INFOID:0000000009883510
Column Shift Model
CAUTION:
• Any time the ignition switch has been disconnected, removed or installed, the keys must be re-regis-
tered in the BCM. Refer to Consult operations IVIS/NVIS.
• Care must be taken not to give axial impact to steering column assembly during removal and instal-
lation.
• Care must be taken not to move steering gear during removal of steering column assembly.
AWGIA0237ZZ
1.
Driver air bag module. Refer to
.
2.
Steering wheel
3.
Steering wheel side cover
4.
Combination switch and spiral cable 5.
Steering column assembly
6.
Collar
7.
Hole cover seal
8.
Clamp
9.
Hole cover mounting plate
10. Hole cover
11. Upper joint
12. Upper shaft
13. Boot clamp
14. Lower joint shaft
15. Boot and clips (plastic)
ST-18
< UNIT REMOVAL AND INSTALLATION >
STEERING COLUMN
Floor Shift Model
CAUTION:
• Any time the ignition switch has been disconnected, removed or installed, the keys must be re-regis-
tered in the BCM. Refer to Consult operations IVIS/NVIS.
• Care must be taken not to give axial impact to steering column assembly during removal and instal-
lation.
• Care must be taken not to move steering gear during removal of steering column assembly.
REMOVAL
1. Remove spiral cable from steering column assembly with combination switches attached. Refer to
2. Remove tilt lever knob from tilt lever by inserting a suitable tool
into slot of tilt lever knob, then depress tab and withdraw tilt lever
knob.
AWGIA0117GB
1.
Driver air bag module. Refer to
2.
Steering wheel
3.
Steering wheel side cover
4.
Combination switch and spiral cable 5.
Steering column assembly
6.
Collar
7.
Hole cover seal
8.
Clamp
9.
Hole cover mounting plate
10. Hole cover
11. Upper joint
12. Upper shaft
13. Boot clamp
14. Lower joint shaft
15. Boot and clips (plastic)
WGIA0061E
STEERING COLUMN
ST-19
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
3. Remove lower driver instrument panel. Refer to
IP-17, "Removal and Installation"
.
4. Remove steering column cover and ignition key finisher. Refer to
IP-11, "Removal and Installation"
5. Remove knee protector screws, then remove knee protector
from vehicle.
6. Disconnect the following:
• Sonar switch
• Adjustable pedal switch
• Wiper switch
• Headlamp switch
• Immobilizer
• Ignition switch
• Spiral cable
7. On models equipped with column shift, disconnect shift cable from steering column. Refer to
T Shift Selector Removal and Installation"
8. Remove lock nut and bolt, then separate lower joint from upper
joint.
9. Remove steering member nuts, then remove steering column
assembly from steering member.
10. Remove hole cover seal and clamp.
11. Remove nuts, then remove hole cover from the lower dash.
LGIA0026E
LGIA0027E
LGIA0028E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст