Nissan Titan. Manual — part 506
SB-4
< REMOVAL AND INSTALLATION >
SEAT BELTS
REMOVAL AND INSTALLATION
SEAT BELTS
Removal and Installation of Front Seat Belt
INFOID:0000000009882835
CREW CAB
AWHIA0225GB
1.
Assist handle
2.
Assist handle screw covers
3.
D-ring anchor bolt cover
4.
Seat belt buckle
5.
Seat belt retractor and belt assembly
(LH)
6.
Anchor cover
7.
Seat belt pre-tensioner connector
8.
Center pillar lower finisher
9.
Seat belt anchor bracket
10. Center pillar
11. Center pillar upper finisher
12. Seat belt height adjuster
13. Seat belt height adjuster finisher
SEAT BELTS
SB-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
KING CAB
REMOVAL AND INSTALLATION OF SEAT BELT RETRACTOR
CAUTION:
• Before servicing SRS, turn the ignition switch off, disconnect both battery terminals and wait at least
three minutes.
WIIA0991E
1.
Seat belt height adjuster
2.
Seat belt height adjuster finisher
3.
Door finisher
4.
Armrest
5.
D-ring anchor bolt cover
6.
Seat belt buckle
7.
Seat belt retractor and belt assembly
(LH)
8.
Anchor cover
9.
Seat belt pre-tensioner connector
10. Lower door finisher
11. Rear door (LH)
SB-6
< REMOVAL AND INSTALLATION >
SEAT BELTS
• For installing/removing seat belt pre-tensioner connector,
insert a thin screwdriver wrapped in tape into the notch, lift
the lock and remove the connector.
• Install the connector with the lock raised, and push the lock
into the connector.
Removal - Crew Cab
CAUTION:
Before servicing the SRS, turn the ignition switch off, disconnect the battery terminals and wait at
least three minutes.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes. Refer to
80, "Removal and Installation"
.
2. Remove the D-ring anchor bolt cover and anchor bolt.
3. Remove the anchor cover and lower seat belt assembly anchor bolt.
• On RH side, disconnect the seat belt tension sensor.
4. Remove the center pillar lower finisher. Refer to
INT-14, "Removal and Installation"
5. Remove the seat belt retractor and belt assembly lower anchor bolt and upper bolt.
6. Disconnect the harness connector from the seat belt pre-tensioner.
7. Remove the front seat belt retractor and belt assembly.
PHIA0341E
1.
Seat belt retractor and belt assembly
RH
2.
Seat belt lower anchor RH (seat belt
tension sensor)
3.
Anchor cover RH (LH similar)
4.
Seat belt lower anchor LH
5.
Seat belt anchor bracket
6.
Seat belt retractor and belt assembly
LH
7.
Center pillar
A.
Lower anchor bolt
B.
Anchor bracket bolt
C.
Retractor anchor bolt
D.
Retractor bolt upper
Front
WHIA0346E
SEAT BELTS
SB-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
Installation - Crew Cab
Installation is in the reverse order of removal.
• Install the seat belt retractor upper bolt first.
• Make sure seat belt height adjuster is locked in the lowest position during installation.
Removal - King Cab
CAUTION:
Before servicing the SRS, turn the ignition switch off, disconnect the battery terminals and wait at
least three minutes.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes. Refer to
80, "Removal and Installation"
2. Remove D-ring anchor bolt cover and bolt.
3. Remove anchor cover and bolt.
4. Remove lower door finisher.
5. Disconnect the harness connector from the seat belt pre-tensioner.
6. Remove seat belt retractor and belt assembly.
Installation - King Cab
Installation is in the reverse order of removal.
REMOVAL AND INSTALLATION OF SEAT BELT BUCKLE
Removal - Bucket Seat
1. Remove the front seat. Refer to
SE-34, "Removal and Installation - Front Seat Assembly"
.
2. Remove screw and seat cushion inner finisher.
3. Remove the anchor bolt and buckle.
4. Disconnect the buckle switch connector from the seat connector.
Installation - Bucket Seat
CAUTION:
• Passenger seat is equipped with Occupant Classification System sensor and control module. Do not
disassemble front passenger seat cushion assembly or remove trim as this will affect the Occupant
Classification System calibration.
• On passenger seat during installation, the wire harness clips must be installed in the holes they were
originally in.
Installation is in the reverse order of removal.
REMOVAL AND INSTALLATION OF CENTER BENCH SEAT BELT AND SEAT BELT BUCKLE
WHIA0128E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст