Nissan Titan. Manual — part 208
HOW TO SET SRT CODE
EC-133
< BASIC INSPECTION >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Always drive the vehicle in safe manner according to traffic conditions and obey all traffic laws.
*1: Depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH), then release the accelerator pedal
and keep it released for more than 10 seconds. Depress the accelerator pedal until vehicle speed is 90 km/h
(56 MPH) again.
*2: Checking the vehicle speed with GST is advised.
• The time required for each diagnosis varies with road surface conditions, weather, altitude, individual driving
habits, etc.
Zone A refers to the range where the time, required for the diagnosis under normal conditions*, is the short-
est.
JSBIA1924GB
EC-134
< BASIC INSPECTION >
[VK56DE]
HOW TO SET SRT CODE
Zone B refers to the range where the diagnosis can still be performed if the diagnosis is not completed within
zone A.
*: Normal conditions refer to the following:
• Sea level
• Flat road
• Ambient air temperature: 20 - 30
°C (68 - 86°F)
• Diagnosis is performed as quickly as possible under normal conditions.
Under different conditions [For example: ambient air temperature other than 20 - 30
°C (68 - 86°F)], diagno-
sis may also be performed.
Work Procedure
INFOID:0000000009886532
1.
CHECK DTC
Check DTC.
Is any DTC detected?
YES
>> Repair malfunction(s) and erase DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK SRT STATUS
WITH CONSULT
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT.
WITHOUT CONSULT
Perform “SRT status” mode with
EC-44, "DIAGNOSIS DESCRIPTION : System Readiness Test (SRT) Code"
.
WITH GST
Select Service $01 with GST.
Is SRT code(s) set?
YES
>> GO TO 11.
NO-1 >> With CONSULT: GO TO 3.
NO-2 >> Without CONSULT: GO TO 4.
3.
DTC CONFIRMATION PROCEDURE
1. Select “SRT WORK SUPPORT” in “DTC & SRT CONFIRMATION” mode with CONSULT.
2. For SRT(s) that is not set, perform the corresponding “DTC CONFIRMATION PROCEDURE” according to
the “Performance Priority” in the “SRT ITEM” table. Refer to
EC-44, "DIAGNOSIS DESCRIPTION : Sys-
tem Readiness Test (SRT) Code"
.
3. Check DTC.
Is any DTC detected?
YES
>> Repair malfunction(s) and erase DTC. Refer to
.
NO
>> GO TO 10.
4.
PERFORM ROAD TEST
• Check the “Performance Priority” in the “SRT ITEM” table. Refer to
EC-44, "DIAGNOSIS DESCRIPTION :
System Readiness Test (SRT) Code"
.
• Perform the most efficient SRT set driving pattern to set the SRT properly. Refer to
DESCRIPTION : Driving Pattern"
.
In order to set all SRTs, the SRT set driving pattern must be performed at least once.
>> GO TO 5.
5.
PATTERN 1
1. Check the vehicle condition;
-
Engine coolant temperature is
−10 to 35°C (14 to 95°F).
-
Fuel tank temperature is more than 0
°C (32°F).
2. Start the engine.
3. Keep engine idling until the engine coolant temperature is greater than 70
°C (158°F)
NOTE:
ECM terminal voltage is follows;
• Engine coolant temperature
HOW TO SET SRT CODE
EC-135
< BASIC INSPECTION >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
-
−10 to 35°C (14 to 95°F): 3.0 - 4.3 V
- 70
°(158°F): Less than 1.4 V
• Fuel tank temperature: Less than 4.1 V
EC-64, "ECM Terminal and Reference Value"
.
>> GO TO 6.
6.
PATTERN 2
1. Drive the vehicle. And depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH), then
release the accelerator pedal and keep it released for more than 10 seconds.
2. Depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH) again
NOTE:
• Checking the vehicle speed with GST is advised.
• When steady-state driving is performed again even after it is interrupted, each diagnosis can be conducted.
In this case, the time required for diagnosis may be extended.
>> GO TO 7.
7.
PATTERN 3
• Operate vehicle following the driving pattern shown in the figure.
• Release the accelerator pedal during deceleration of vehicle speed
from 90 km/h (56 MPH) to 0 km/h (0 MPH).
>> GO TO 8.
8.
PATTERN 4
• Operate vehicle following the driving pattern shown in the figure.
- Drive the vehicle in a proper gear at 60 km/h (38 MPH) and main-
tainthe speed.
- Release the accelerator pedal fully at least 5 seconds.
- Repeat the above two steps at least 5 times.
>> GO TO 9.
9.
PATTERN 5
• The accelerator pedal must be held very steady during steady-state driving.
• If the accelerator pedal is moved, the test must be conducted again.
>> GO TO 10.
10.
CHECK SRT STATUS
WITH CONSULT
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT.
WITHOUT CONSULT
Perform “SRT status” mode with
EC-44, "DIAGNOSIS DESCRIPTION : System Readiness Test (SRT) Code"
.
WITH GST
Select Service $01 with GST.
Is SRT(s) set?
PBIB2244E
JSBIA0160GB
EC-136
< BASIC INSPECTION >
[VK56DE]
HOW TO SET SRT CODE
YES
>> GO TO 11.
NO
>> Call TECH LINE or take appropriate action.
11.
CHECK PERMANENT DTC
NOTE:
Permanent DTC cannot be checked with a tool other than CONSULT or GST.
With CONSULT
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT.
With GST
Select Service $0A with GST.
Is permanent DTC(s) detected?
YES
>> Refer to
.
NO
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст