Nissan Titan. Manual — part 106
REAR DOOR LOCK
DLK-133
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4. While pulling the outside handle, remove the door handle
escutcheon in order shown.
5. While pulling the outside handle, slide it toward the rear of vehi-
cle to remove in order shown.
6. Remove the front gasket (1) and rear gasket (2).
7. Remove the inside handle screws.
8. Remove the bolts and the door lock assembly.
CAUTION:
Do not reuse bolts.
LIIA1971E
LIIA0532E
ALKIA0893ZZ
PIIB5812E
DLK-134
< REMOVAL AND INSTALLATION >
REAR DOOR LOCK
9. While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket and door lock assembly.
10. Disconnect the outside handle cable.
INSTALLATION
Installation is in the reverse order of removal.
PIIA3558E
PIIA5059E
TAIL GATE
DLK-135
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TAIL GATE
Exploded View
INFOID:0000000009878847
Removal and Installation
INFOID:0000000009878848
CAUTION:
Use two people when removing or installing tail gate assembly due to its heavy weight.
TAIL GATE
Removal
1. Lower tail gate to access rear camera harness connector bracket (if equipped). Release tab on bracket,
then pull out rear camera harness and disconnect connector.
2. Release tail gate stay assembly (LH/RH).
1.
Tail gate liner cover (if equipped)
2.
Tail gate inner panel
3.
Tail gate rubber bumper
4.
Washer
5.
Tail gate stay assembly
6.
Tail gate hinge assembly (LH), body
side
7.
Tail gate ring (LH)
8.
Tail gate hinge assembly (LH), gate
side
9.
Tail gate control assembly
10. Rear camera
11. Tail gate handle
12. Tail gate lock cylinder
13. Emblem
14. Tail gate
15. Tail gate hinge assembly (RH), gate
side
16. Tail gate ring (RH)
17. Tail gate hinge assembly (RH), body
side
18. Gas stay (if equipped)
19. Gas stay bracket
20. Tail gate cover
21. Rubber bumper
22. Tail gate latch assembly (LH/RH)
AWKIA2078ZZ
DLK-136
< REMOVAL AND INSTALLATION >
TAIL GATE
3. While holding tail gate at 45 degree angle, pull tailgate out from hinge assembly (LH), then slide tail gate
out of hinge assembly (RH) and remove.
Installation
Installation is in the reverse order of removal.
GAS STAY
Removal
WARNING:
The gas stay is under high pressure. Remove the gas stay only with the tail gate fully closed. Injury
may result if the gas stay is removed when the tail gate is open.
1. Remove the RH rear combination lamp assembly. Refer to
EXL-150, "Removal and Installation"
.
2. Remove the gas stay.
Installation
Installation is in the reverse order of removal.
Tail Gate Gas Stay Disposal
INFOID:0000000009878849
1. Fix tail gate gas stay (1) using a vise (C).
2. Using hacksaw (A) slowly make 2 holes in the tail gate gas stay,
in numerical order as shown.
CAUTION:
• When cutting a hole on tail gate gas stay, always cover
hacksaw with shop cloths (B) to avoid scattering metal
fragments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
LIIA1984E
JMKIA3336ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст