Nissan Titan. Manual — part 361
FRONT DOOR GLASS AND REGULATOR
GW-19
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Fitting Inspection
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts, and glass and guide rail bolts to correct the glass position.
FRONT DOOR GLASS REGULATOR ASSEMBLY
Removal
1. Remove the front door finisher. Refer to
INT-10, "Removal and Installation"
2. Position aside the vapor barrier.
3. Remove the hole cover over rear glass bolt.
4. Operate the power window main switch to raise/lower the door window until the glass bolts can be seen.
5. Remove the inside seal.
6. Remove the glass bolts.
7. Raise the front door glass and hold it in place with suitable tool.
8. Disconnect the harness connector from the regulator assembly.
9. Remove the bolts and the regulator assembly.
Disassembly And Assembly
Remove the regulator motor from the regulator assembly.
Inspection After Removal
Check the regulator assembly for the following items. If a malfunc-
tion is detected, replace or grease it.
• Wire wear
• Regulator deformation
• Grease condition for each sliding part
The arrows in the figure show the application points of the body
grease.
Installation
If any of the following work has been done, reset the power window motor limit switch.
• Removal and installation of the regulator assembly.
• Removal and installation of the power window motor from the regulator.
• Installation of a new glass window.
• Installation of a new glass run.
WINDOW REGULATOR RESET PROCEDURE
1. Connect the door harness connector to the power window motor, and rotate the motor more than 5 turns
in the glass raising (up) direction.
2. Install the power window motor onto the regulator.
3. Install the regulator assembly into the door and secure regulator assembly with the nuts and bolt.
4. Install the glass into the door and align with the regulator, then install the glass bolts.
5. Raise the glass to the top position.
CAUTION:
LIIA0670E
Power Window Motor Up Direction
• LH motor rotate counterclockwise
• RH motor rotate clockwise
Regulator assembly nuts
and bolt
: 7.5 N·m (0.77 kg-m, 66 in-lb)
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
GW-20
< UNIT REMOVAL AND INSTALLATION >
FRONT DOOR GLASS AND REGULATOR
Do not operate the glass automatically to raise the glass to the top.
6. Reposition the vapor barrier.
7. Install the front door finisher. Refer to
INT-10, "Removal and Installation"
.
REAR DOOR GLASS AND REGULATOR
GW-21
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS AND REGULATOR
Rear Door Glass
INFOID:0000000009878928
REMOVAL
1. Remove the rear door finisher. Refer to
INT-10, "Removal and Installation"
.
2. Position aside the vapor barrier.
3. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
4. Remove the inside seal.
5. Remove the glass bolts and the glass.
INSTALLATION
1. Install the glass from outside to ensure that it is in both the front and rear glass channels. Tighten glass
the bolts to the specified torque.
2. Install the inside seal.
3. Reposition the vapor barrier.
4. Install the rear door finisher. Refer to
INT-10, "Removal and Installation"
FITTING INSPECTION
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)], and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolt, guide
rail bolts, and glass and carrier plate bolts to correct the glass position.
SIIA0290E
AWKIA1734ZZ
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
GW-22
< UNIT REMOVAL AND INSTALLATION >
REAR DOOR GLASS AND REGULATOR
Rear Door Glass Regulator Assembly
INFOID:0000000009878929
REMOVAL
1. Remove the rear door finisher. Refer to
INT-10, "Removal and Installation"
.
2. Position aside the vapor barrier.
3. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
4. Remove the inside seal.
5. Remove the glass bolts, raise the glass and hold in place with
suitable tool.
6. Remove the bolts and the regulator and guide channel from the
panel.
7. Disconnect the connector for the regulator assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Gear wear
• Regulator deformation
• Spring damage
• Grease condition for each sliding part
INSTALLATION
Installation is in the reverse order of removal.
SIIA0290E
SIIA0291E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст