Nissan Titan. Manual — part 144
DLN-148
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 3S1410]
REAR PROPELLER SHAFT
UNIT REMOVAL AND INSTALLATION
REAR PROPELLER SHAFT
Removal and Installation
INFOID:0000000009886065
2WD Models (short wheel base)
AWDIA1050ZZ
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Sleeve yoke
5.
Journal
6.
Center support bearing
7.
Center support bearing bracket
8.
Clamp
9.
Boot
10. Slip yoke
11. Flange yoke
Front
REAR PROPELLER SHAFT
DLN-149
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 3S1410]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
2WD Models (long wheel base)
4WD Models (long wheel base)
AWDIA1051ZZ
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Sleeve yoke
5.
Journal
6.
Center support bearing
7.
Center support bearing bracket
8.
Slip yoke
9.
Flange yoke
Front
AWDIA1052ZZ
DLN-150
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 3S1410]
REAR PROPELLER SHAFT
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove under cover (if equipped).
2. Move the A/T shift selector to the N position and release the parking brake.
3. Put matching marks on the rear propeller shaft flange yoke and
the companion flange of the rear final drive as shown.
CAUTION:
For matching marks, use paint. Do not damage the rear pro-
peller shaft flange yoke or the companion flange.
4. Remove the center support bearing bracket nuts (
), and
remove the propeller shaft from the rear final drive.
INSPECTION AFTER REMOVAL
• Inspect the propeller shaft runout. If runout exceeds the limit,
replace the propeller shaft assembly. Refer to
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Sleeve yoke
5.
Journal
6.
Center support bearing
7.
Center support bearing bracket
8.
Slip yoke
9.
Flange yoke
: Front
WDIA0065E
WDIA0066E
PDIA0420E
REAR PROPELLER SHAFT
DLN-151
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 3S1410]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• While holding the flange yoke on one side, check axial play of the
joint as shown. If the journal axial play exceeds the specification,
repair or replace the journal parts.
• Check the propeller shaft tube for bend and damage. If damage is
detected, replace the propeller shaft assembly.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, check for vibration by driving the vehicle. Refer to
DLN-146, "NVH Troubleshooting Chart"
.
• If propeller shaft assembly of final drive assembly has been
replaced, connect them as follows:
- Face companion flange mark (A) of the final drive (1) upward. With
the mark (A) faced upward, couple the propeller shaft and the final
drive so that the matching mark (B) of the propeller shaft (2) can be
positioned as close as possible with the matching mark (C) of the
final drive companion flange.
- Tighten propeller shaft and final drive bolts and nuts of the to spec-
DLN-148, "Removal and Installation"
.
CAUTION:
Do not reuse the bolts and nuts. Always install new ones.
Journal axial play : 0.02 mm (0.0008 in) or less
LDIA0117E
PDIA0892J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст