Nissan Titan. Manual — part 345
DRIVE SHAFT
FAX-13
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
7. Install the boot securely into the grooves (indicated by * marks)
as shown.
CAUTION:
If there is grease on boot mounting surfaces (indicated by *
marks) of shaft and housing, boot may come off. Remove
all grease from surfaces.
8. Check that the boot installation length (L) is the length indicated
below. Insert a suitable tool into the large end of the boot, as
shown. Bleed air from the boot to prevent boot deformation.
CAUTION:
• The boot may break if the boot installation length is less than the specified value.
• Do not contact inside surface of boot with tip of the suitable tool.
9. Secure the large and small ends of the boot with the new boot
bands as shown.
NOTE:
Discard the old boot bands and use new ones for assembly.
10. After installing the sliding joint housing to the drive shaft, rotate the boot to check that the boot is posi-
tioned correctly. If the boot is not positioned correctly, reposition the boot and secure the boot using a new
boot band.
Wheel Side
1. Insert the Genuine NISSAN Grease or equivalent, into the joint
sub-assembly serration hole until the grease begins to ooze
from the ball groove and serration hole. Refer to
NORTH AMERICA : Fluids and Lubricants"
(United States and
Canada),
MA-16, "FOR MEXICO : Fluids and Lubricants"
(Mex-
ico). After inserting the grease, use a shop cloth to wipe off the
grease that has oozed out.
2. Wrap the serrated part of the drive shaft with tape. Install the
boot band and boot onto the shaft. Do not damage the boot.
NOTE:
Discard the old boot band and boot and use a new one for
assembly.
3. Remove the protective tape wound around the serrated part of
the drive shaft.
Boot installation
length (L)
: Refer to
.
WDIA0287E
SFA395
SDIA1127E
SFA800
FAX-14
< UNIT DISASSEMBLY AND ASSEMBLY >
DRIVE SHAFT
4. Attach the circlip to the drive shaft making sure circlip fits
securely into groove on drive shaft. Then install drive shaft nut to
end of joint sub-assembly, and press-fit the circlip using a suit-
able tool as shown.
NOTE:
Discard the old circlip and use a new one for assembly.
5. Insert the specified quantity of Genuine NISSAN Grease or
equivalent, into the joint sub-assembly and the large end of the
MA-15, "FOR NORTH AMERICA : Fluids and
(United States and Canada),
(Mexico).
6. Install the boot securely into the grooves (indicated by the *
marks) as shown.
CAUTION:
If there is grease on the boot mounting surfaces (indicated
by the * marks) of the drive shaft and joint sub-assembly,
the boot may come off. Remove all grease from the drive
shaft surfaces.
7. Check that the boot installation length (L) is the specified length.
Insert a suitable tool into the large end of the boot, as shown.
Bleed the air from the boot to prevent boot deformation.
CAUTION:
• The boot may break if the boot installation length is less than the specified length.
• Do not contact inside surface of boot with the tip of the suitable tool.
8. Secure large and small ends of the boot using new boot bands
using tool as shown.
NOTE:
Discard the old boot bands and use new ones for assembly.
• Secure boot band so that dimension (M) meets specification
as shown.
9. After installing the housing to the shaft, rotate the boot to check that it is positioned correctly. If the boot is
not positioned correctly, remove the old boot bands then reposition the boot and secure the boot with new
boot bands.
Grease capacity : Refer to
RAC0049D
Boot installation
length (L)
: Refer to
.
Tool number : KV40107300 ( — )
WDIA0288E
RAC1133D
Dimension (M)
: Refer to
.
DSF0047D
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-15
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000009886177
Drive Shaft
INFOID:0000000009886178
Boot Bands
INFOID:0000000009886179
Unit: mm (in)
Axial end play
0.05 mm (0.002 in) or less
Drive shaft joint type
Final drive side
Rzeppa
Wheel side
Rzeppa
Grease
Quality
NISSAN Genuine Grease or
equivalent
Capacity
Final drive side
130 - 150 g (4.58 - 5.29 oz)
Wheel side
145 - 165 g (5.11 - 5.82 oz)
Boot length
Final drive side (L
)
145 mm (5.71 in)
Wheel side (L)
168.4 mm (6.63 in)
WDIA0055E
Dimension (M)
1.0 - 4.0 (0.039 - 0.157)
DSF0047D
FL-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
FL
A
FL
N
O
P
CONTENTS
FUEL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
FUEL SYSTEM . . . . . . . . . . . . .
General Precaution . . . . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
BASIC INSPECTION . . . . . . . . .
FUEL SYSTEM . . . . . . . . . . . . .
Checking Fuel Line . . . . . . . . . . . . ...
UNIT REMOVAL AND INSTALLATION . ...
FUEL TANK . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . ...
FUEL LEVEL SENSOR UNIT, FUEL FILTER
AND FUEL PUMP ASSEMBLY . . . . . .
Removal and Installation . . . . . . . . . . .
EVAP CANISTER . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Component Inspection . . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
FUEL LEVEL SENSOR UNIT, FUEL FILTER
AND FUEL PUMP ASSEMBLY . . . . . .
Exploded View . . . . . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст