Nissan Titan. Manual — part 103
HOOD
DLK-121
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
1. Pull the hood lock release cable through the hole in dash lower panel into the engine room.
Be careful not to bend the cable too much, keeping the radius
100mm (3.94 in) or more.
2. Make sure the hood lock release cable is not offset from the
positioning grommet, and from inside the vehicle, push the
grommet into the dash lower hole securely.
3. Apply the sealant around the grommet at (*) mark.
4. Install the hood lock release cable securely to the hood lock.
5. After installing, check the hood lock adjustment and hood lock
release handle operation.
Hood Lock Control Inspection
INFOID:0000000009878838
CAUTION:
If the hood lock release cable is bent or deformed, replace it.
1. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height.
2. While operating the hood lock release handle, carefully make
sure the front edge of the hood is raised by approx. 20 mm (0.79
in). Also make sure the hood lock release handle returns to the
original position.
3. Check the hood lock lubrication condition. If necessary, apply a
suitable multi-purpose grease to the points shown.
PIIA0173E
PIIA0174E
PIIA1086E
PIIA0176E
DLK-122
< REMOVAL AND INSTALLATION >
HOOD
Hood Stay Disposal
INFOID:0000000009878839
1. Fix hood stay (1) using a vise (C).
2. Using hacksaw (A) slowly make 2 holes in the hood stay, in
numerical order as shown.
CAUTION:
• When cutting a hole on hood stay, always cover hacksaw
with shop cloths (B) to avoid scattering metal fragments
or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
JMKIA3336ZZ
A: 20 mm (0.8 in)
B: Cut at the groove.
JMKIA3609ZZ
DOOR
DLK-123
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR
Fitting Adjustment
INFOID:0000000009878840
KING CAB
AWKIA1728GB
E.
4.5
± 1.0 mm (0.177 ± 0.039 in)
F.
6.5
± 1.0 mm (0.256 ± 0.039 in)
DLK-124
< REMOVAL AND INSTALLATION >
DOOR
CREW CAB
Front Door
Longitudinal clearance and surface height adjustment at front end
1. Remove the front fender. Refer to
EXT-23, "Removal and Installation"
.
2. Loosen the hinge bolts.
3. Raise the front door at rear end to adjust.
4. Tighten the hinge bolts
5. Install the front fender. Refer to
EXT-23, "Removal and Installation"
Rear Door Crew Cab
Longitudinal clearance and surface height adjustment at rear end
1. Remove the center pillar upper finisher. Refer to
INT-14, "Removal and Installation"
.
2. Accessing from inside the vehicle, loosen the nuts. Open the rear door, and raise the rear door at rear end
to adjust.
3. Tighten the nuts to specification.
4. Install the center pillar upper garnish. Refer to
INT-14, "Removal and Installation"
Rear Door King Cab
Longitudinal clearance and surface height adjustment at front end
1. With the door open, support and loosen the hinge to door nuts.
2. Adjust the door position as necessary.
3. Tighten the nuts to specification.
AWKIA1730GB
E.
4.5
± 1.0 mm (0.177 ± 0.039 in)
F.
6.5
± 1.0 mm (0.256 ± 0.039 in)
Rear door hinge nuts
: 24.5 N·m (2.5 kg-m, 18 ft-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст