Nissan Titan. Manual — part 311
EM-48
< REMOVAL AND INSTALLATION >
INTAKE VALVE TIMING CONTROL
Intake Valve Timing Control Position Sensor (LH)
INFOID:0000000009886425
REMOVAL
1. Remove engine room cover using power tool. Refer to
EM-25, "Removal and Installation"
.
2. Remove air duct and resonator assembly. Refer to
EM-26, "Removal and Installation"
3. Disconnect intake valve timing control position sensor harness connector (LH).
4. Remove intake valve timing control position sensor (LH) (1) and
O-ring (2) from Intake valve timing control solenoid valve cover
(LH) (3).
CAUTION:
Do not reuse O-ring.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Lubricate O-ring with engine oil before installing.
• Do not reuse O-ring.
Intake Valve Timing Control Position Sensor (RH)
INFOID:0000000009886426
REMOVAL
1. Remove engine room cover using power tool. Refer to
EM-25, "Removal and Installation"
.
2. Disconnect intake valve timing control position sensor harness connector (RH).
3. Remove intake valve timing control position sensor (RH) (1) and
O-ring (2) from Intake valve timing control solenoid valve cover
(RH) (3).
CAUTION:
Do not reuse O-ring.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Lubricate O-ring with engine oil before installing.
• Do not reuse O-ring.
Camshaft Position Sensor (PHASE)
INFOID:0000000009886427
REMOVAL
1. Remove engine room cover using power tool. Refer to
EM-25, "Removal and Installation"
.
2. Remove air duct and resonator assembly. Refer to
EM-26, "Removal and Installation"
3. Disconnect camshaft position sensor harness connector.
AWBIA0141ZZ
Intake valve timing control position sensor bolt
: 9.0 N·m (0.92 kg-m, 80 in-lb)
AWBIA0143ZZ
Intake valve timing control position sensor bolt
: 9.0 N·m (0.92 kg-m, 80 in-lb)
INTAKE VALVE TIMING CONTROL
EM-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4. Remove camshaft position sensor (2) and O-ring (3) from Intake
valve timing control solenoid valve cover (LH) (1).
CAUTION:
Do not reuse O-ring.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Lubricate O-ring with engine oil before installing.
• Do not reuse O-ring.
AWBIA0142ZZ
Camshaft position sensor bolt
: 9.0 N·m (0.92 kg-m, 80 in-lb)
EM-50
< REMOVAL AND INSTALLATION >
TIMING CHAIN COVER
TIMING CHAIN COVER
Exploded View
INFOID:0000000009886428
Removal and Installation
INFOID:0000000009886429
REMOVAL
1. Remove the upper oil pan. Refer to
EM-35, "Removal and Installation"
.
2. Remove the intake valve timing control solenoid (LH) and (RH). Refer to
. (LH), and
EM-47, "Intake Valve Timing Control Solenoid Valve (RH)"
3. Remove the intake valve timing control position sensor (LH) and (RH). Refer to
ing Control Position Sensor (LH)"
EM-48, "Intake Valve Timing Control Position Sensor (RH)"
(RH).
4. Remove the camshaft position sensor (PHASE). Refer to
EM-48, "Camshaft Position Sensor (PHASE)"
5. Remove the crankshaft driven fan pulley and pulley bracket. Refer to
EM-15, "Drive Belt Auto-Tensioner
6. Remove the drive belt auto-tensioner and idler pulley.
1.
Intake valve timing control position
sensor (RH)
2.
Intake valve timing control position
sensor (LH)
3.
Intake valve timing control solenoid
valve cover (LH)
4.
Intake valve timing control solenoid
valve (RH)
5.
O-ring
6.
Camshaft position sensor (PHASE)
7.
Crankshaft pulley bolt
8.
Crankshaft pulley
9.
Chain tensioner cover
10. Front oil seal
11.
Intake valve timing control solenoid
valve (RH)
12
Intake valve timing control solenoid
valve cover (RH)
13. Front cover
AWBIA1016GB
TIMING CHAIN COVER
EM-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
7. Remove the intake valve timing control solenoid valve cover
(RH) (A) and intake valve timing control solenoid valve cover
(LH) (B) as follows:
a. Loosen and remove the bolts in the reverse order as shown.
b. Cut the liquid gasket and remove the covers using Tool.
CAUTION:
Do not damage mating surfaces.
8. Obtain compression TDC of No. 1 cylinder as follows:
a. Turn the crankshaft pulley clockwise to align the TDC identifica-
tion notch (without paint mark) with the timing indicator on the
front cover.
9. Remove drive plate lower cover.
10. Loosen the crankshaft pulley bolts. Use Tool (A) to secure the
crankshaft as shown.
a. Remove the crankshaft pulley from the crankshaft using suitable
tool.
• Set the bolts in the two bolt holes [M6 x 1.0 mm (0.04 in)] on
the front surface.
NOTE:
The dimension between the centers of the two bolt holes is 61
mm (2.40 in).
Tool number
: KV10111100 (J-37228)
AWBIA0815ZZ
KBIA2476E
Tool number
— (J-47245)
LBIA0455E
KBIA2477E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст