Nissan Titan. Manual — part 303
EM-16
< PERIODIC MAINTENANCE >
AIR CLEANER FILTER
AIR CLEANER FILTER
Exploded View
INFOID:0000000009886402
Removal and Installation (Viscous paper type)
INFOID:0000000009886403
REMOVAL
NOTE:
• The viscous paper type filter does not need cleaning between replacement intervals.
• Replace the air filter as necessary for periodic maintenance. Refer to
MA-9, "FOR NORTH AMERICA : Intro-
duction of Periodic Maintenance"
, (United States and Canada),
MA-12, "FOR MEXICO : Introduction of Peri-
1. Remove the air cleaner case (upper).
2. Remove the air cleaner filter from the air cleaner case (lower).
INSTALLATION
1. Install the new air cleaner filter in the air cleaner case (lower).
2. Install the air cleaner case (upper).
1.
Air cleaner case (lower)
2.
Air cleaner filter
3.
Air cleaner case (upper)
4.
Air duct and resonator assembly
Front
ALBIA0413GB
SPARK PLUG
EM-17
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SPARK PLUG
Exploded View
INFOID:0000000009886404
Removal and Installation
INFOID:0000000009886405
REMOVAL
1. Remove ignition coil. Refer to
EM-40, "Removal and Installation"
.
CAUTION:
Do not shock ignition coil.
2. Remove spark plug using suitable tool.
CAUTION:
Do not drop or shock spark plug.
INSPECTION AFTER REMOVAL
• Do not use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be used.
1.
Ignition coil
2.
Spark plug
WBIA0796E
SEM294A
Cleaner air pressure
: Less than 588 kPa (6 kg/cm
2
,
85 psi)
Cleaning time
: Less than 20 seconds
SMA773C
EM-18
< PERIODIC MAINTENANCE >
SPARK PLUG
• Checking and adjusting plug gap is not required between change
intervals.
INSTALLATION
Installation is in the reverse order of removal.
Spark Plug Types
*: Always check with the Parts Department for the latest parts information.
CAUTION:
Do not drop or shock spark plug.
SMA806CA
Make
NGK
Model
Standard model
FFV model
Standard type*
DILFR5A-11
DILFR5A-11D
Gap (Nominal)
1.1 mm (0.043 in)
1.1 mm (0.043 in)
CAMSHAFT VALVE CLEARANCE
EM-19
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CAMSHAFT VALVE CLEARANCE
Valve Clearance
INFOID:0000000009886406
INSPECTION
NOTE:
Perform the following inspection after removal, installation or replacement of camshaft or valve-related parts,
or if there are unusual engine conditions due to changes in valve clearance over time (starting, idling, and/or
noise).
1. Warm up the engine. Then stop the engine.
2. Remove the air cleaner and resonator assembly. Refer to
EM-26, "Removal and Installation"
3. Remove the (RH) bank and (LH) bank rocker covers using power tool. Refer to
.
4. Turn the crankshaft pulley in the normal direction (clockwise
when viewed from engine front) to align TDC identification notch
(without paint mark) with timing indicator.
5. At this time, make sure both the intake and exhaust cam noses
of No. 1 cylinder (top front on LH bank) face outside.
• If they do not face outside, turn crankshaft pulley once more.
KBIA2476E
KBIA0400J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст