Nissan Titan. Manual — part 650
ASSEMBLY
TM-283
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8. Make sure that brake band (1) does not close input speed sen-
sor hole (A).
9. Connect TCM connector (1) and transmission range switch con-
nector (2).
10. Install A/T assembly harness connector to control valve with
TCM.
11. Connect TCM connectors.
12. Install O-ring to A/T assembly harness connector.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
JSDIA1318ZZ
JSDIA1317ZZ
SCIA5450E
SCIA5447E
SCIA5155E
TM-284
< UNIT DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
13. Install new O-ring (1) in plug (2).
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
• O-ring should be free of contamination.
14. Install plug (2) to bracket (1).
15. Install plug (1) [with bracket (2)] to control valve with TCM and
tighten bolt (
) to specified torque.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve.
16. Install control valve with TCM in transmission case.
CAUTION:
• Make sure that input speed sensor is securely installed
into input speed sensor hole (A).
• Hang down output speed sensor harness toward outside
so as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve cutout is engaged with
manual plate projection.
JSDIA1313ZZ
JSDIA1312ZZ
Bracket bolt
: 7.9 N·m (0.81 kg-m, 70 in-lb)
JSDIA1311ZZ
1
: Brake band
JSDIA1318ZZ
SCIA5035E
ASSEMBLY
TM-285
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
17. Install bolts (A), (B) and (C) to control valve with TCM.
18. Tighten bolt (A), (B) and (C) temporarily to prevent dislocation.
After that tighten them in order (A
→ B → C), and then tighten
other bolts.
19. Connect output speed sensor connector (1).
20. Securely fasten output speed sensor harness with terminal clip
(
).
: Front
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8077E
: Front
Bolt symbol
A
B
C
Number of bolts
5
6
1
Length mm (in)
42 (1.65)
55 (2.17)
40 (1.57)
Tightening torque
N·m (km-g, in-lb)
7.9 (0.81, 70)
With ATF applied
7.9 (0.81, 70)
SCIA8078E
JSDIA1319ZZ
JSDIA1320ZZ
TM-286
< UNIT DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
21. Pull down A/T assembly harness connector.
CAUTION:
Do not damage connector.
22. Install snap ring to A/T assembly harness connector.
23. Install magnets in oil pan.
24. Install oil pan to transmission case. Refer to
TM-199, "Removal and Installation"
.
25. Install torque converter.
a. Pour ATF into torque converter.
NOTE:
• Approximately 2 liters (2-1/8 US qt. 1-3/4 Imp qt) of fluid is
required for a new torque converter.
• When reusing old torque converter, add the same amount of
fluid as was drained.
SCIA5299E
SCIA5300E
SCIA5200E
SAT428DA
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст