Nissan Titan. Manual — part 626
ROAD TEST
TM-187
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Read the gear position.
Is downshifting correctly performed?
YES
>> GO TO 5.
NO
>> Record the malfunction, GO TO 5.
4.
CHECK SHIFT-DOWN
During D
5
driving, move gear selector from D
→ 4 → 3 → 2 → 1.
With CONSULT
Read the gear position.
Is downshifting correctly performed?
YES
>> GO TO 5.
NO
>> Record the malfunction, GO TO 5.
5.
CHECK ENGINE BRAKE
Does engine braking effectively reduce speed in M
1
position (with manual mode) or 1
1
position (without man-
ual mode)?
YES
>> 1. Stop the vehicle.
2. Carry out the self-diagnostics. Refer to
TM-38, "CONSULT Function (TRANSMISSION)"
.
NO
>> Record the malfunction, then continue the trouble diagnosis.
TM-188
< REMOVAL AND INSTALLATION >
SHIFT CONTROL SYSTEM
REMOVAL AND INSTALLATION
SHIFT CONTROL SYSTEM
Exploded View
INFOID:0000000009885909
Floor shift models
AWDIA0956GB
1.
Shift selector handle
2.
A/T finisher
3.
A/T shift selector assembly
4.
Position lamp
5.
Control cable
6.
Lock plate
SHIFT CONTROL SYSTEM
TM-189
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Column shift models
A/T Shift Selector Removal and Installation
INFOID:0000000009885910
REMOVAL
Floor shift
1. Disconnect negative battery terminal. Refer to
PG-80, "Removal and Installation"
2. Remove A/T finisher. Refer to
IP-18, "Removal and Installation"
.
3. Disconnect A/T shift selector harness connector.
4. Disconnect control cable.
5. Remove A/T shift selector assembly.
Column shift
1. Remove the steering column. Refer to
ST-17, "Removal and Installation"
.
2. Remove the control cable lock plate clip and remove the control
cable from column shifter pin.
3. Remove the A/T shift selector.
INSTALLATION
Installation is in the reverse order of removal.
• After installation is completed, be sure to check A/T position and adjust as necessary. Refer to
.
AWDIA0782ZZ
1.
A/T shift selector
2.
Control cable
3.
A/T control cable lock plate clip
LCIA0343E
TM-190
< REMOVAL AND INSTALLATION >
SHIFT CONTROL SYSTEM
Inspection and Adjustment
INFOID:0000000009885911
ADJUSTMENT OF A/T POSITION
1. Loosen nut of control cable.
2. Place transmission range switch and A/T shift selector in “P”
position.
3. After pushing the control cable in the direction shown with a
force of 9.8 N·m (1 kg-m, 2.2 lb-ft), release it. This is in the natu-
ral state, tighten control cable nut to specifications.
CHECKING OF A/T POSITION
NOTE:
Following procedure will cover both column and floor shift selectors.
1. Place shift selector in “P” position, and turn ignition switch ON
(engine stop).
2. Make sure shift selector can be moved from “P” position when
brake pedal is depressed. Also make sure shift selector can be
moved from “P” position only when brake pedal is depressed.
3. Move the shift selector and check for excessive effort, sticking,
noise or rattle.
4. Confirm the shift selector stops at each position with the feel of
engagement when it is moved through all the positions. Check
whether or not the actual position the shift selector is in matches
the position shown by the shift position indicator and the trans-
mission body.
5. Confirm the back-up lamps illuminate only when shift selector is placed in the “R” position. Confirm the
back-up lamps do not illuminate when shift selector is pushed against “R” position in the “P” or “N” posi-
tion.
6. Confirm the engine can only be started with the shift selector in the “P” and “N” positions.
7. Make sure transmission is locked completely when shift selector is in the “P” position.
Control cable nut
: 14.6 N·m (1.5 kg-m, 11 ft-lb)
LCIA0345E
LCIA0325E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст