Nissan Titan. Manual — part 663
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
WT-17
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
1. Carry out ID registration of all transmitters. Refer to
WT-6, "ID Registration Procedure"
.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
>> GO TO 2
2.
REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. Refer to
51, "Transmitter (Pressure Sensor)"
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES
>> GO TO 3
NO
>> GO TO
3.
DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
2. Check all tire pressures with CONSULT within 5 minutes.
Does “DATA MONITOR ITEM” display tire pressure as normal without any warning lamp?
YES
>> Inspection End.
NO
>> Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
INFOID:0000000009885642
Perform preliminary check. Refer to
.
WT-18
< DTC/CIRCUIT DIAGNOSIS >
C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION
C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION
Description
INFOID:0000000009885643
Air pressure data from one or more transmitters is out of range.
DTC Logic
INFOID:0000000009885644
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT within 5 minutes.
Does “DATA MONITOR ITEM” display tire pressure as normal without any warning lamp?
YES
>> Inspection End.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009885645
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
MALFUNCTION CODE NO. 35, 36, 37 OR 38 (DTC C1716, C1717, C1718 OR C1719)
1.
CHECK ALL TIRE PRESSURES
Check all tire pressures. Refer to
Are there any tires with pressure of 64 psi or more?
YES
>> Adjust tire pressure to specified value.
NO
>> GO TO 2
2.
ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters. Refer to
WT-6, "ID Registration Procedure"
2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
3. Check all tire pressures with CONSULT within 15 minutes after vehicle speed becomes 17 km/h (11
MPH).
Does “DATA MONITOR ITEM” display 64 psi or more?
DTC
CONSULT
DTC detecting condition
C1716
[PRESSDATA - ERR] FL
Air pressure data from FL transmitter is malfunctioning.
C1717
[PRESSDATA - ERR] FR
Air pressure data from FR transmitter is malfunctioning.
C1718
[PRESSDATA - ERR] RR
Air pressure data from RR transmitter is malfunctioning.
C1719
[PRESSDATA - ERR] RL
Air pressure data from RL transmitter is malfunctioning.
C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION
WT-19
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
YES
>> Replace transmitter. Refer to
WT-51, "Transmitter (Pressure Sensor)"
. GO TO 3.
NO
>> GO TO 3
3.
ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT within 5 minutes.
Does “DATA MONITOR ITEM” display tire pressure as normal without any warning lamp?
YES
>> Inspection End.
NO
>> Proceed to the inspection applicable to DTC.
Special Repair Requirement
INFOID:0000000009885646
Perform preliminary check. Refer to
.
WT-20
< DTC/CIRCUIT DIAGNOSIS >
C1729 VEHICLE SPEED SIGNAL
C1729 VEHICLE SPEED SIGNAL
Description
INFOID:0000000009885647
The vehicle speed signal is not being detected by the BCM.
DTC Logic
INFOID:0000000009885648
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
1. On “SELECT DIAG MODE”, select the “SELF-DIAG RESULT” screen.
2. Check display contents on ”SELF DIAG RESULT” screen.
Is the “CAN COMM CIRCUIT” displayed in the self-diagnosis display?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009885649
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
MALFUNCTION CODE NO. 52 (DTC C1729)
1.
CHECK SELF-DIAGNOSTIC RESULTS
1. On “SELECT DIAG MODE”, select the “SELF-DIAG RESULT” screen.
2. Check display contents on ”SELF DIAG RESULT” screen.
Is the “CAN COMM CIRCUIT” displayed in the self-diagnosis display?
YES
>> Perform trouble diagnosis for CAN communication system.
NO
>> Check combination meter. Refer to
MWI-28, "CONSULT Function (METER/M&A)"
Special Repair Requirement
INFOID:0000000009885650
Perform preliminary check. Refer to
.
DTC
CONSULT
DTC detecting condition
C1729
VHCL SPEED SIG ERR
Vehicle speed signal is in error.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст