Nissan Pathfinder (2011 year). Manual — part 610
TM-226
< UNIT DISASSEMBLY AND ASSEMBLY >
DISASSEMBLY
32. Straighten terminal clip (
) to free output speed sensor har-
ness.
33. Remove bolts (A), (B) and (C) from control valve with TCM.
•
: Front
34. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the manual valve notch and
manual plate height. Remove it vertically.
35. Remove plug (1) with bracket (2) from control valve with TCM.
36. Remove bracket (1) from plug (2).
JSDIA1320ZZ
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8077E
SCIA5260E
JSDIA1311ZZ
JSDIA1312ZZ
2011 Pathfinder
DISASSEMBLY
TM-227
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
37. RemoveO-ring (1) from plug (2).
38. Remove O-ring from A/T assembly harness connector.
39. Disconnect TCM connectors.
CAUTION:
Do not damage connectors.
40. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
41. Disconnect TCM connector (1) and transmission range switch
connector (2).
CAUTION:
Do not damage connectors.
JSDIA1313ZZ
SCIA5155E
SCIA5447E
SCIA5448E
JSDIA1317ZZ
2011 Pathfinder
TM-228
< UNIT DISASSEMBLY AND ASSEMBLY >
DISASSEMBLY
42. Remove rear extension assembly (2WD models) or adapter case assembly (4WD models) according to
the following procedures.
a.
2WD models
i.
Remove bolts for rear extension assembly and transmission
case.
ii.
Tap rear extension assembly with soft hammer.
iii. Remove rear extension assembly (with needle bearing) from
transmission case.
b.
4WD models
SCIA6941E
SCIA5028E
SCIA5029E
2011 Pathfinder
DISASSEMBLY
TM-229
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
i.
Remove adapter case to transmission case bolts.
• Self-sealing bolts (2)
ii.
Remove brackets (1) (if equipped).
iii. Tap adapter case assembly using suitable tool.
iv. Remove adapter case assembly (with needle bearing) from
transmission case.
v.
Remove gasket from transmission case.
WCIA0563E
SCIA5201E
SCIA5186E
SCIA5231E
2011 Pathfinder
TM-230
< UNIT DISASSEMBLY AND ASSEMBLY >
DISASSEMBLY
43. Remove bearing race from output shaft.
44. Remove output shaft from transmission case by rotating left and
right.
45. Remove parking gear from output shaft.
46. Remove seal rings from output shaft.
47. Remove needle bearing from transmission case.
SCIA5245E
SCIA5030E
SCIA5247E
SCIA5209E
SCIA5031E
2011 Pathfinder
DISASSEMBLY
TM-231
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
48. Remove output speed sensor (1) from transmission case.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings or any foreign material to get on
the sensor's front edge magnetic area.
• Do not place in an area affected by magnetism.
49. Remove reverse brake snap ring using two flat-bladed screw-
drivers.
NOTE:
Press out snap ring from the transmission case oil pan side gap
using a flat-bladed screwdriver, and remove it using a another
screwdriver.
50. Remove reverse brake retaining plate from transmission case.
• Check facing for burns, cracks or damage. If necessary,
replace the plate.
51. Remove N-spring from transmission case.
52. Remove reverse brake drive plates, driven plates and dish plate
from transmission case.
•
Check facing for burns, cracks or damage. If necessary,
replace the plate.
53. Remove snap ring using suitable tool.
: Bolt
JSDIA1321ZZ
SCIA5032E
SCIA5214E
SCIA2322E
SCIA2323E
2011 Pathfinder
TM-232
< UNIT DISASSEMBLY AND ASSEMBLY >
DISASSEMBLY
54. Remove spring retainer and return spring from transmission
case.
55. Remove seal rings from drum support.
56. Remove needle bearing from drum support edge surface.
57. Remove reverse brake piston from transmission case using
compressed air. Refer to
.
CAUTION:
Care should be taken not to abruptly blow air. It makes the
piston incline, and as a result, it becomes hard to disas-
semble the pistons.
SCIA2324E
SCIA3333E
SCIA2796E
SCIA5047E
2011 Pathfinder
DISASSEMBLY
TM-233
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
58. Remove D-rings from reverse brake piston.
59. Knock out retaining pin using suitable tool.
60. Remove manual shaft retaining pin using suitable tool.
61. Remove manual plate (with parking rod) from manual shaft.
62. Remove parking rod from manual plate.
SCIA6330E
SCIA2328E
SCIA2329E
SCIA5715E
SCIA5220E
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст