Nissan Pathfinder (2011 year). Manual — part 356
EC-902
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
P2A00, P2A03 A/F SENSOR 1
>>
INSPECTION END
2011 Pathfinder
ASCD BRAKE SWITCH
EC-903
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ASCD BRAKE SWITCH
Component Description
INFOID:0000000006244599
When the brake pedal is depressed, ASCD brake switch is turned
OFF and stop lamp switch is turned ON. ECM detects the state of
the brake pedal by two kinds of input (ON/OFF signal).
Diagnosis Procedure
INFOID:0000000006244600
1.
CHECK OVERALL FUNCTION-I
With CONSULT-III
1. Turn ignition switch ON.
2. Select “BRAKE SW 1” in “DATA MONITOR” mode with CONSULT-III.
3. Check “BRAKE SW 1” indication under the following conditions.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check voltage between ECM terminal 108 and ground under the
following conditions.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
2.
CHECK ASCD BRAKE SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ASCD brake switch harness connector.
3. Turn ignition switch ON.
BBIA0560E
CONDITION
INDICATION
Brake pedal: Fully released
ON
Brake pedal: Slightly depressed
OFF
CONDITION
VOLTAGE
Brake pedal: Fully released
Battery voltage
Brake pedal: Slightly depressed
Approximately 0 V
MBIB0061E
BBIA0560E
2011 Pathfinder
EC-904
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
ASCD BRAKE SWITCH
4. Check voltage between ASCD brake switch terminal 1 and
ground with CONSULT-III or tester.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING PART
Check the following.
• Fuse block (J/B) connector E160
• 10 A fuse (No. 12)
• Harness for open or short between ASCD brake switch and fuse
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check harness continuity between ECM terminal 108 and ASCD brake switch terminal 2.
Refer to Wiring Diagram.
4. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK ASCD BRAKE SWITCH
EC-904, "Component Inspection"
OK or NG
OK
>> GO TO 6.
NG
>> Replace ASCD brake switch. Refer to
6.
CHECK INTERMITTENT INCIDENT
GI-37, "Intermittent Incident"
>>
INSPECTION END
Component Inspection
INFOID:0000000006244601
ASCD BRAKE SWITCH
1. Turn ignition switch OFF.
2. Disconnect ASCD brake switch harness connector.
Voltage: Battery voltage
PBIB0857E
Continuity should exist.
2011 Pathfinder
ASCD BRAKE SWITCH
EC-905
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3. Check harness continuity between ASCD brake switch terminals
1 and 2 under the following conditions.
If NG, adjust ASCD brake switch installation, refer to
, and perform step 3 again.
Condition
Continuity
Brake pedal: Fully released
Should exist.
Brake pedal: Slightly depressed
Should not exist.
SEC023D
2011 Pathfinder
EC-906
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
ASCD INDICATOR
ASCD INDICATOR
Component Description
INFOID:0000000006244602
ASCD indicator lamp illuminates to indicate ASCD operation status. Lamp has two indicators, CRUISE and
SET, and is integrated in combination meter.
CRUISE indicator illuminates when MAIN switch on ASCD steering switch is turned ON to indicate that ASCD
system is ready for operation.
SET indicator illuminates when the following conditions are met.
• CRUISE indicator is illuminated.
• SET/COAST switch on ASCD steering switch is turned ON while vehicle speed is within the range of the
ASCD setting.
SET indicator remains lit during ASCD control.
Diagnosis Procedure
INFOID:0000000006244603
1.
CHECK OVERALL FUNCTION
Check ASCD indicator under the following conditions.
OK or NG
OK
>>
INSPECTION END
NG
>> GO TO 2.
2.
CHECK DTC
Check that DTC U0101 or U1001 is not displayed.
OK or NG
OK
>> GO TO 3.
NG
>> Perform trouble diagnosis for DTC U0101 or U1001. Refer to
EC-613, "DTC Confirmation Proce-
EC-614, "DTC Confirmation Procedure"
3.
CHECK COMBINATION METER FUNCTION
MWI-27, "CONSULT-III Function (METER/M&A)"
.
OK or NG
OK
>> GO TO 4.
NG
>> Go to
4.
CHECK INTERMITTENT INCIDENT
GI-37, "Intermittent Incident"
>>
INSPECTION END
ASCD INDICATOR
CONDITION
SPECIFICATION
CRUISE LAMP
• Ignition switch: ON
• MAIN switch: Pressed at the 1st
time
→
at the 2nd time
ON
→
OFF
SET LAMP
• MAIN switch: ON
• When vehicle speed : Between
40 km/h (25 MPH) and 144 km/h
(89 MPH)
• ASCD: Operating
ON
• ASCD: Not operating
OFF
2011 Pathfinder
COOLING FAN
EC-907
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
COOLING FAN
Description
INFOID:0000000006244604
COMPONENT DESCRIPTION
Cooling Fan Motor
The cooling fan operates at each speed when the current flows in the cooling fan motor as per the following.
Diagnosis Procedure
INFOID:0000000006244605
1.
CHECK IPDM E/R POWER SUPPLY AND GROUND CIRCUIT
OK or NG
OK
>> GO TO 2.
NG
>> Follow the instructions on
.
2.
CHECK COOLING FAN MOTOR POWER SUPPLY CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector E120.
3. Disconnect cooling fan motor (1) harness connector.
4. Check harness continuity between the following terminals;
cooling fan motor terminal 1 and IPDM E/R terminal 20,
cooling fan motor terminal 2 and IPDM E/R terminal 24.
Refer to Wiring Diagram.
5. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 3.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
3.
CHECK COOLING FAN MOTER GROUND CIRCUIT FOR OPEN OR SHORT
1. Check harness continuity between the following terminals;
cooling fan motor terminal 3 and ground,
cooling fan motor terminal 4 and ground.
Refer to Wiring Diagram.
2. Also check harness for short to power.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to power in harness or connectors.
4.
CHECK COOLING FAN MOTOR
EC-908, "Component Inspection"
OK or NG
OK
>> GO TO 5.
Cooling fan speed
Cooling fan motor terminals
(+)
(
−
)
Low (LOW)
1
3 and 4
2
3 and 4
High (HI)
1 and 2
3 and 4
Continuity should exist.
ALBIA0355ZZ
Continuity should exist.
2011 Pathfinder
EC-908
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
COOLING FAN
NG
>> Replace cooling fan motor. Refer to
.
5.
CHECK INTERMITTENT INCIDENT
Perform
GI-37, "Intermittent Incident"
.
OK or NG
OK
>> INSPETION END
NG
>> Repair or replace harness or connector.
Component Inspection
INFOID:0000000006244606
COOLING FAN MOTOR
1. Disconnect cooling fan motor harness connector.
2. Supply cooling fan motor terminals with battery voltage and
check operation.
Cooling fan motor should operate.
If NG, replace cooling fan motor. Refer to
Cooling fan speed
Cooling fan motor terminals
(+)
(
−
)
Low
1
3 and 4
2
3 and 4
High
1 and 2
3 and 4
SEF734W
2011 Pathfinder
ELECTRICAL LOAD SIGNAL
EC-909
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ELECTRICAL LOAD SIGNAL
Description
INFOID:0000000006244607
The electrical load signal (Headlamp switch signal, etc.) is transferred via the CAN communication line.
Diagnosis Procedure
INFOID:0000000006244608
1.
CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-I
1. Turn ignition switch ON.
2. Connect CONSULT-III and select “DATA MONITOR” mode.
3. Select “LOAD SIGNAL” and check indication under the following conditions.
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 4.
2.
CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-II
Check “LOAD SIGNAL” indication under the following conditions.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 5.
3.
CHECK HEATER FAN SIGNAL CIRCUIT OVERALL FUNCTION
Select “HEATER FAN SW” and check indication under the following conditions.
OK or NG
OK
>>
INSPECTION END
NG
>> GO TO 6.
4.
CHECK REAR WINDOW DEFOGGER SYSTEM
>>
INSPECTION END
5.
CHECK HEADLAMP SYSTEM
>>
INSPECTION END
6.
CHECK HEATER FAN CONTROL SYSTEM
HAC-4, "How to Perform Trouble Diagnosis For Quick And Accurate Repair"
Perform Trouble Diagnosis For Quick And Accurate Repair"
.
Condition
Indication
Rear window defogger switch: ON
ON
Rear window defogger switch: OFF
OFF
Condition
Indication
Lighting switch: ON at 2nd position
ON
Lighting switch: OFF
OFF
Condition
Indication
Heater fan control switch: ON
ON
Heater fan control switch: OFF
OFF
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст