Nissan Pathfinder (2011 year). Manual — part 433
GW-10
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
LAIA0071E
2011 Pathfinder
WINDSHIELD GLASS
GW-11
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
UNIT REMOVAL AND INSTALLATION
WINDSHIELD GLASS
Removal and Installation
INFOID:0000000006247195
REMOVAL
1. Remove inside mirror. Refer to
MIR-15, "Removal and Installation"
.
2. Remove the front pillar upper finisher. Refer to
INT-19, "Removal and Installation"
.
3. Partially remove the headlining (front edge). Refer to
INT-22, "Removal and Installation"
4. Remove cowl top cover. Refer to
EXT-21, "Removal and Installation"
.
5. Apply a protective tape around the windshield glass to protect the painted surface from damage.
6. Remove glass using piano wire or power cutting tool and an inflatable pump bag.
• If the windshield glass is to be reused, mark the body and the glass with mating marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:
• When the windshield glass is to be reused, do not use a cutting knife or power cutting tool.
• Be careful not to scratch the glass when removing.
• Do not set or stand glass on its edge. Small chips may develop into cracks.
INSTALLATION
Installation is in the reverse order of removal.
1.
Molding
2.
Windshield
3.
Windshield position pins
4.
Mirror base
5.
Insulator
LIIA1684E
PIIA0186E
2011 Pathfinder
GW-12
< UNIT REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
• Use a genuine NISSAN Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger compartment air pressure when a door is closed.
• The molding must be installed securely so that it is in position and leaves no gap.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
If affected by vapor inhalation, immediately move to an area with fresh air.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the windshield in case of an accident.
CAUTION:
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed
on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidities. The curing time will increase
under lower temperatures and lower humidities.
2011 Pathfinder
WINDSHIELD GLASS
GW-13
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
1.
Windshield glass
2.
Molding
3.
Roof
4.
Urethane
5.
A-pillar
6.
Primer
7.
Cowl top panel
8.
Insulator
9.
Instrument panel
10. Cowl top cover
A.
Primer area (top and sides)
B.
Primer area (bottom)
C.
Bond area (top and sides)
D.
Bond area (bottom)
a.
7.0 mm (0.27 in)
WIIA1032E
2011 Pathfinder
GW-14
< UNIT REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
Repairing Water Leaks for Windshield
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the windshield area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
b.
10.0 mm (0.39 in)
c.
22.0 mm (0.78 in)
d.
20.0 mm (0.78 in)
e.
28.0 mm (1.10 in)
f.
12.0 mm (0.47 in)
g.
15.0 mm (0.59 in)
2011 Pathfinder
FRONT DOOR GLASS AND REGULATOR
GW-15
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
FRONT DOOR GLASS AND REGULATOR
Front Door Glass
INFOID:0000000006247196
REMOVAL
1. Remove the front door finisher. Refer to
INT-15, "Removal and Installation"
2. Position aside the vapor barrier.
3. Temporarily reconnect the power window switch.
4. Operate the power window main switch to raise/lower the door
window until the glass bolts can be seen.
5. Partially remove the inside seal.
6. Remove the glass bolts.
7. While holding the door window, raise it at the rear and pull the
glass out of the sash toward the outside of the door.
INSTALLATION
Installation is in the reverse order of removal.
• Check the glass for proper fit. Follow the "FITTING INSPECTION" procedure.
• On the drivers door, reset the motor.
FITTING INSPECTION
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts, and glass and guide rail bolts to correct the glass position.
Front Door Glass Regulator
INFOID:0000000006247197
REMOVAL
1. Remove the front door finisher. Refer to
INT-15, "Removal and Installation"
2. Position aside the vapor barrier.
3. Temporarily reconnect the power window switch.
LIIA1686E
LIIA1687E
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
2011 Pathfinder
GW-16
< UNIT REMOVAL AND INSTALLATION >
FRONT DOOR GLASS AND REGULATOR
4. Operate the power window main switch to raise/lower the door
window until the glass bolts can be seen.
5. Remove the glass bolts.
6. Raise the front door glass and hold it in place with suitable tool
(A) .
7. Disconnect the harness connector from the regulator assembly.
8. Remove the bolts and the regulator assembly.
DISASSEMBLY AND ASSEMBLY
Remove the regulator motor from the regulator assembly.
INSPECTION AFTER REMOVAL
LIIA1686E
PIIB3510J
Front
WIIA1033E
2011 Pathfinder
FRONT DOOR GLASS AND REGULATOR
GW-17
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Wire wear
• Regulator deformation
• Grease condition for each sliding part
INSTALLATION
1. Install the regulator assembly.
a. Loosely install the top rear regulator bolt to use along with the temporary holds on the window motor to
install the assembly in the door.
b. Install the top front regulator bolt.
c. Install the bottom front regulator bolt.
d. Install the bottom rear regulator bolt.
e. Tighten the top rear regulator bolt.
f.
Install the top window motor bolt.
g. Install the lower window motor bolt
h. Install the rear window motor bolt.
2. Connect the harness connector to the regulator assembly.
Front
Regulator and motor bolts : 5.1 N·m (0.58 kg-m, 50 in-lb)
WIIA1033E
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст