Nissan Pathfinder (2011 year). Manual — part 413
EXL-150
< UNIT REMOVAL AND INSTALLATION >
HAZARD SWITCH
HAZARD SWITCH
Removal and Installation
INFOID:0000000006247715
REMOVAL
1. Remove cluster lid C. Refer to
2. Remove the screws and remove the hazard switch.
INSTALLATION
Installation is in the reverse order of removal.
2011 Pathfinder
HIGH-MOUNTED STOP LAMP
EXL-151
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HIGH-MOUNTED STOP LAMP
High-Mounted Stop Lamp
INFOID:0000000006247716
BULB REPLACEMENT
The high-mounted stop lamp bulbs are not serviceable.
REMOVAL AND INSTALLATION
Removal
1. Remove back door finisher and window garnish. Refer to
INT-27, "Removal and Installation"
.
2. Disconnect high-mounted stop lamp connector.
3. Remove nuts and remove high-mounted stop lamp.
Installation
Installation is in the reverse order of removal.
LKIA0576E
2011 Pathfinder
EXL-152
< UNIT REMOVAL AND INSTALLATION >
LICENSE PLATE LAMP
LICENSE PLATE LAMP
Bulb Replacement
INFOID:0000000006247717
LICENSE PLATE LAMP
Removal
1. Remove back door finisher. Refer to
EXT-23, "Removal and Installation"
2. Turn bulb socket counterclockwise and remove bulb socket.
3. Remove license plate lamp bulb.
Installation
Installation is in the reverse order of removal.
Removal and Installation
INFOID:0000000006247718
LICENSE PLATE LAMP
Removal
1. Remove license lamp finisher. Refer to
EXT-23, "Removal and Installation"
.
2. Disconnect license plate lamp harness connector.
3. Remove license plate lamp screw and remove license plate lamp.
Installation
Installation is in the reverse order of removal.
2011 Pathfinder
REAR COMBINATION LAMP
EXL-153
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR COMBINATION LAMP
Bulb Replacement
INFOID:0000000006247719
REMOVAL
1. Remove rear combination lamp bolts.
2. Pull rear combination lamp to remove from the vehicle.
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb.
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation
INFOID:0000000006247720
REMOVAL
1. Remove rear combination lamp bolts.
2. Pull rear combination lamp to remove from the vehicle.
3. Disconnect rear combination lamp connector.
INSTALLATION
Installation is in the reverse order of removal.
WKIA4168E
2011 Pathfinder
EXL-154
< SERVICE DATA AND SPECIFICATIONS (SDS)
BULB SPECIFICATIONS
SERVICE DATA AND SPECIFICATIONS (SDS)
BULB SPECIFICATIONS
Headlamp
INFOID:0000000006247721
*: Always check with the Parts Department for the latest parts information.
Exterior Lamp
INFOID:0000000006247722
*: Always check with the Parts Department for the latest parts information.
Item
Wattage (W)*
Low/High
55/65
Item
Wattage (W)*
Front combination lamp
Turn signal lamp/parking lamp
28/8
Side marker
3.8
Rear combination lamp
Stop/Tail lamp
27/8
Turn signal lamp
27
Back-up lamp
18
Front fog lamp
55
License plate lamp
5
High-mounted stop lamp
*
2011 Pathfinder
EXT-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
EXT
A
B
EXT
N
O
P
CONTENTS
EXTERIOR
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . .....
Service Notice . . . . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover . ..
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
CLIP LIST . . . . . . . . . . . . . . .
Descriptions for Clips . . . . . . . . . . . ....
PERIODIC MAINTENANCE . . . . . . ..
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . .
Work Flow . . . . . . . . . . . . . . . .....
Generic Squeak and Rattle Troubleshooting . . ..
Diagnostic Worksheet . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
FRONT BUMPER . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
REAR BUMPER . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FRONT GRILLE . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
COWL TOP . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
FRONT FENDER . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
LICENSE LAMP FINISHER . . . . . . . ..
Removal and Installation . . . . . . . . . . .
FENDER PROTECTOR . . . . . . . . .
Component . . . . . . . . . . . . . . . ..
Removal and Installation of Front Fender Protec-
tor . . . . . . . . . . . . . . . . . . .
Removal and Installation of Rear Fender Protector
MUDGUARD . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
RUNNING BOARDS . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
ROOF RACK . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DOOR OUTSIDE MOLDING . . . . . . . .
Removal and Installation . . . . . . . . . . .
SIDE GUARD MOLDING . . . . . . . . ..
Removal and Installation . . . . . . . . . . .
2011 Pathfinder
EXT-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006245321
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000006245322
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
2011 Pathfinder
PRECAUTIONS
EXT-3
< PRECAUTION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
Service Notice
INFOID:0000000006245323
• When removing or installing various parts, place a cloth or padding on the vehicle body to prevent scratches.
• Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to soil or
damage them.
• Apply sealing compound where necessary when installing parts.
• When applying sealing compound, be careful that the sealing compound does not protrude from parts.
• When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust preven-
tion measures.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000006245324
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precaution for Work
INFOID:0000000006826811
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components.
- Water soluble dirt: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the dirty
area.
Then rub with a soft and dry cloth.
- Oily dirt: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the dirty area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
PIIB3706J
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст