Nissan Pathfinder (2011 year). Manual — part 576
STEERING COLUMN
ST-19
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING COLUMN
Removal and Installation
INFOID:0000000006247245
CAUTION:
• Do not exert any axial load or impact to the steering column.
• Do not move the steering gear while the steering column assembly is removed.
• Any time the ignition switch has been removed and installed, the keys must be re-registered in the
BCM. Refer to CONSULT–III Operation Manual IVIS/NVIS.
REMOVAL
1. Remove the spiral cable with the combination switches attached from the steering column assembly.
SR-7, "Removal and Installation"
.
2. Remove the instrument lower panel LH. Refer to
IP-12, "Removal and Installation"
.
3. Disconnect the following:
• Ignition key lamp
• Immobilizer
• Ignition switch
4. Disconnect key interlock cable from steering column (if equipped). Refer to
.
1.
Driver air bag module
2.
Steering wheel center nut
3.
Steering wheel
4.
Combination switch and spiral cable 5.
Steering column assembly and igni-
tion switch
6.
Collar
7.
Hole cover seal
8.
Clamp
9.
Hole cover mounting plate
10. Hole cover
11. Upper joint
12. Upper shaft
13. Boot clamp
14. Lower joint shaft
15. Boot and clips (plastic)
AWGIA0198GB
2011 Pathfinder
ST-20
< UNIT REMOVAL AND INSTALLATION >
STEERING COLUMN
5. Remove the lock nut and bolt from the upper joint, then separate
the upper joint from the upper shaft.
CAUTION:
• Do not reuse the lock nut.
6. Remove the three nuts and bolt from the steering column
assembly, then remove the steering column assembly from the
steering member.
7. Remove the hole cover seal and clamp.
8. Remove the hole cover nuts, then remove the hole cover from
the dash panel.
9. Remove the bolt from the lower joint of the lower joint shaft, then
remove the lower joint shaft from the vehicle.
CAUTION:
• Do not damage the lower joint.
INSPECTION AFTER REMOVAL
• Check for damage to the steering column jacket tube. If damage is found, replace the steering column with a
new one.
CAUTION:
• Do not exert any axial load or impact to the steering column.
• Replace the column if it is depleted of grease, worn, damaged, or if any scratches or coating sepa-
ration is present on the shaft seal area.
• If the vehicle has been in a collision, or if noises are heard coming
from the steering column, check column length (L) as shown. If out
of specification, replace the steering column as an assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
LGIA0027E
LGIA0028E
LGIA0029E
Steering column
length (L)
Refer to
.
AWGIA0147ZZ
2011 Pathfinder
STEERING COLUMN
ST-21
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
When installing the steering column, finger-tighten all of the lower bracket and joint bolts; then tighten
them to specification. Do not apply undue stress to the steering column.
NOTE:
• With the wheels in the straight ahead position, align the slit of the
lower joint with the projection on the dust cover. Insert the joint until
surface (A) contacts surface (B).
• After installation, inspect the steering column for proper operation.
INSPECTION AFTER INSTALLATION
• Check the tilt device for proper tilt range.
• Check that the steering wheel turns smoothly to the left and right
locks.
• Check that the number of turns are the same from the straight-for-
ward position to the left and right locks.
• Check that the steering wheel is in the neutral position when driv-
ing straight ahead.
SST491C
Tilt range (A)
WGIA0083E
2011 Pathfinder
ST-22
< UNIT REMOVAL AND INSTALLATION >
POWER STEERING GEAR AND LINKAGE
POWER STEERING GEAR AND LINKAGE
Removal and Installation
INFOID:0000000006247246
CAUTION:
Spiral cable may snap due to steering operation if the steering column is separated from the steering
gear assembly. Therefore secure the steering wheel to avoid turning.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Set front wheels in the straight-ahead position.
2. Drain the power steering fluid.
3. Remove the front tires from the vehicle, using power tool.
4. Remove the under cover, using power tool.
5. On 4WD models, remove the front final drive, then support the drive shafts, using suitable wire. Refer to
DLN-356, "Removal and Installation"
DLN-390, "Removal and Installation"
(M205).
6. Remove the stabilizer bar brackets and reposition the stabilizer bar. Refer to
.
7. Remove the cotter pins at the steering outer sockets.
CAUTION:
Do not reuse the cotter pins.
8. Loosen the outer socket nuts.
9. Remove the steering outer sockets from the steering knuckles,
using Tool, then remove the nuts.
CAUTION:
• Do not damage the outer socket boots.
• Do not damage the outer socket threads. Thread the ball
joint nut onto the end of the outer socket during removal.
1.
Cotter pin
2.
Mounting bracket
3.
Mounting insulator
4.
Steering gear assembly
5.
Washer
Front
AWGIA0136GB
Tool number
: HT72520000 (J-25730-A)
WGIA0130E
2011 Pathfinder
POWER STEERING GEAR AND LINKAGE
ST-23
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
10. Remove the high-pressure and low-pressure piping from the
steering gear assembly, then drain the fluid from the piping.
CAUTION:
Do not reuse O-ring.
11. Remove the pinch bolt from the lower joint shaft, then separate
the lower joint from the steering gear assembly.
CAUTION:
• Do not damage the lower joint.
12. Remove the nuts and bolts of the steering gear assembly, using
power tool, then remove the steering gear assembly from the
vehicle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse O-ring.
• With the steering wheel in the straight ahead position, align the slit
of the lower joint with the projection on the dust cover. Insert the
joint until surface (A) contacts surface (B).
• After removing/installing or replacing steering components, check
wheel alignment. Refer to
FSU-7, "Front Wheel Alignment"
.
• After adjusting wheel alignment, adjust neutral position of the
steering angle sensor. Refer to
STEERING ANGLE SENSOR NEUTRAL POSITION : Special
(TYPE 1),
STEERING ANGLE SENSOR NEUTRAL POSITION : Special
(TYPE 2).
• Bleed the air from the steering hydraulic system. Refer to
"Air Bleeding Hydraulic System"
.
INSPECTION AFTER INSTALLATION
• Check that the steering wheel turns smoothly to the left and right locks.
• Check that the number of turns are the same from the straight-forward position to the left and right locks.
• Check that the steering wheel is in the neutral position when driving straight ahead.
LGIA0032E
LGIA0029E
LGIA0024E
SST491C
2011 Pathfinder
ST-24
< UNIT REMOVAL AND INSTALLATION >
POWER STEERING OIL PUMP
POWER STEERING OIL PUMP
Removal and Installation
INFOID:0000000006247247
VQ40DE ENGINE
VK56DE ENGINE
AWGIA0137GB
1.
Connector
2.
Suction pipe
3.
O-ring
4.
Bracket
5.
Pulley
6.
Lock washer
7.
Body assembly
8.
Copper sealing washers
Apply Genuine NISSAN PSF or
equivalent
LGIA0038E
1.
Bracket
2.
Spring washer
3.
Pulley
4.
Power steering pump
5.
High pressure hose bracket
6.
O-ring
7.
Suction pipe
Front
Apply Genuine NISSAN PSF or
equivalent
2011 Pathfinder
POWER STEERING OIL PUMP
ST-25
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
POWER STEERING OIL PUMP
Removal
1. Drain the power steering fluid from the reservoir tank.
2. Remove the engine room cover. Refer to
EM-25, "Removal and Installation"
3. Remove cooling fan assembly. Refer to
CO-22, "Removal and Installation (Motor driven type)"
4. Remove the air duct assembly. Refer to
EM-26, "Removal and Installation"
5. Remove the serpentine drive belt from the auto tensioner and power steering oil pump. Refer to
EM-153, "Removal and Installation"
6. Disconnect the pressure sensor electrical connector.
7. Remove the high pressure and low pressure piping from the power steering oil pump. Refer to
8. Remove the power steering oil pump bolts, then remove the power steering pump.
Installation
Installation is in the reverse order of removal.
• On VQ40DE, install the bolts and tighten to specification in the
order shown.
• After installation, bleed the air from the hydraulic circuit thoroughly.
ST-13, "Air Bleeding Hydraulic System"
.
NOTE:
Belt tension is automatic and requires no adjustment.
POWER STEERING OIL PUMP BRACKET (VQ40DE)
Removal
1. Remove the power steering oil pump.
2. Remove the bolts and the power steering oil pump bracket.
Installation
1. Position the bracket and install the bracket to block bolts finger tight.
2. Tighten the bolts to specification in order as shown.
3. Install the power steering oil pump.
Power steering pump to
bracket bolt (1)
: 64.7 Nm (6.6 kg–m, 48 ft–lb)
Power steering pump to
block bolt (2)
: 28 Nm (2.9 kg–m, 21 ft–lb)
ALGIA0047ZZ
Bracket to front of block
bolt (1)
: 61.3 Nm (6.3 kg–m, 45 ft–lb)
Bracket to side of block
bolt (2)
: 61.3 Nm (6.3 kg–m, 45 ft–lb)
ALGIA0048ZZ
2011 Pathfinder
ST-26
< UNIT REMOVAL AND INSTALLATION >
HYDRAULIC LINE
HYDRAULIC LINE
Removal and Installation
INFOID:0000000006247248
Refer to the following illustrations for hydraulic line removal and installation.
CAUTION:
Do not reuse O-rings or copper sealing washers.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
VQ40DE ENGINE
AWGIA0195GB
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст