Nissan Pathfinder (2011 year). Manual — part 170
DLK-226
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE) : Diagnosis Procedure
INFOID:0000000006827765
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
Is the fuse blown?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit.
NO
>> GO TO 2
2.
CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Terminal No.
Signal name
Fuses and fusible link No.
57
Battery power supply
21 (10A)
70
G (50A)
11
Ignition ACC or ON
4 (10A)
38
Ignition ON or START
1 (10A)
Connector
Terminals
Power
source
Condition
Voltage (V) (Ap-
prox.)
(+)
(-)
M18
11
Ground
ACC
power
supply
Ignition
switch
ACC or
ON
Battery voltage
38
Ground
Ignition
power
supply
Ignition
switch ON
or START
Battery voltage
M20
57
Ground
Battery
power
supply
Ignition
switch
OFF
Battery voltage
70
Ground
Battery
power
supply
Ignition
switch
OFF
Battery voltage
LIIA2415E
2011 Pathfinder
POWER SUPPLY AND GROUND CIRCUIT
DLK-227
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Inspection End.
NO
>> Repair or replace harness.
BCM
Ground
Continuity
Connector
Terminal
M20
67
Yes
LIIA0915E
2011 Pathfinder
DLK-228
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR SWITCH
DOOR SWITCH
Description
INFOID:0000000006245609
Detects door open/close condition.
Component Function Check
INFOID:0000000006245610
1.
CHECK FUNCTION
With CONSULT-III
Check door switches in data monitor mode with CONSULT-III.
Is the inspection result normal?
YES
>> Door switch is OK.
NO
>> Refer to
DLK-228, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006245611
Regarding Wiring Diagram information, refer to
DLK-279, "Wiring Diagram - Without Intelligent Key System"
1.
CHECK DOOR SWITCHES INPUT SIGNAL
With CONSULT-III
Check door switches ("DOOR SW-DR", "DOOR SW-AS", "DOOR SW-RL", "DOOR SW-RR", "BACK DOOR
SW") in DATA MONITOR mode with CONSULT–III.
• When doors are open:
• When doors are closed:
Without CONSULT-III
Check voltage between BCM connector M18 or M19 terminals 12, 13, 43, 47, 48 and ground.
Monitor item
Condition
DOOR SW-DR
CLOSE
→
OPEN: OFF
→
ON
DOOR SW-AS
DOOR SW-RL
DOOR SW-RR
BACK DOOR SW
DOOR SW-DR
:ON
DOOR SW-AS
:ON
DOOR SW-RL
:ON
DOOR SW-RR
:ON
BACK DOOR SW
:ON
DOOR SW-DR
:OFF
DOOR SW-AS
:OFF
DOOR SW-RL
:OFF
DOOR SW-RR
:OFF
BACK DOOR SW
:OFF
2011 Pathfinder
DOOR SWITCH
DLK-229
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Door switch circuit is OK.
NO
>> GO TO 2
2.
CHECK DOOR SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door switch and BCM.
3. Check continuity between BCM connector (A) M18, M19 terminals 12, 13, 43, 47, 48 and door switch con-
nector (B) B8 (Front LH), B108 (Front RH), B18 (Rear LH), B116 (Rear RH) terminal 2 or back door latch
connector (C) D502 terminal 3.
4. Check continuity between door switch connector (B) B8 (Front
LH), B108 (Front RH), B18 (Rear LH), B116 (Rear RH) terminal
2 or back door latch connector (C) D502 terminal 3 and ground.
Is the inspection result normal?
YES
>> (Front and rear doors) GO TO 3.
YES
>> (Back door) GO TO 4.
NO
>> Repair or replace harness.
3.
CHECK DOOR SWITCH
• Check continuity between door switch terminals.
Connec-
tor
Item
Terminals
Condition
Voltage (V)
(Approx.)
( + )
( – )
M19
Back door
switch/latch
43
Ground
Open
↓
Closed
0
↓
Battery voltage
Front door
switch LH
47
Rear door
switch LH
48
M18
Front door
switch RH
12
Rear door
switch RH
13
LIIA1041E
2 - 47
:Continuity should exist
2 - 12
:Continuity should exist
2 - 48
:Continuity should exist
2 - 13
:Continuity should exist
3 - 43
:Continuity should exist
2 - Ground
:Continuity should not exist
3 - Ground
:Continuity should not exist
ALKIA1701ZZ
2011 Pathfinder
DLK-230
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR SWITCH
Is the inspection result normal?
YES
>> Door switch circuit is OK.
NO
>> Replace door switch.
4.
CHECK BACK DOOR LATCH CIRCUIT
• Check continuity between back door latch connector terminal 4 and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK BACK DOOR LATCH SWITCH
• Check continuity between back door latch switch terminals.
Is the inspection result normal?
YES
>> Back door latch switch circuit is OK.
NO
>> Replace back door latch.
Switch
Terminals
Condition
Continuity
Door switch
2 – Ground
Open
Yes
Closed
No
ALKIA0747ZZ
Connector
Terminals
Continuity
Back door latch
4 – Ground
Yes
ALKIA1703ZZ
Switch
Terminals
Condition
Continuity
Back door latch
3 – 4
Open
Yes
Closed
No
ALKIA1702ZZ
2011 Pathfinder
GLASS HATCH AJAR SWITCH
DLK-231
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
GLASS HATCH AJAR SWITCH
Description
INFOID:0000000006245612
Detects glass hatch open/close condition.
Component Function Check
INFOID:0000000006245613
1.
CHECK FUNCTION
With CONSULT-III
Check glass hatch switch in data monitor mode with CONSULT-III.
Is the inspection result normal?
YES
>> Glass hatch switch is OK.
NO
>> Refer to
DLK-231, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000006245614
Regarding Wiring Diagram information, refer to
DLK-279, "Wiring Diagram - Without Intelligent Key System"
1.
CHECK GLASS HATCH AJAR SWITCH INPUT SIGNAL
With CONSULT-III
Check glass hatch ajar switch "GLASS HATCH SW" in DATA MONITOR mode with CONSULT–III.
• When glass hatch is open:
• When glass hatch is closed:
Without CONSULT-III
Check voltage between BCM connector M19 terminals 42 and ground.
Is the inspection result normal?
YES
>> Glass hatch ajar switch circuit is OK.
NO
>> GO TO 2
2.
CHECK GLASS HATCH AJAR SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect glass hatch ajar switch and BCM.
3. Check continuity between BCM connector (A) M19 terminal 42 and glass hatch ajar switch connector (B)
D503 terminal 1.
Monitor item
Condition
GLASS HATCH SW
CLOSE
→
OPEN: OFF
→
ON
GLASS HATCH SW
:ON
GLASS HATCH SW
:OFF
Connector
Item
Terminals
Condition
Voltage (V)
(Approx.)
( + )
( – )
M19
BCM
42
Ground
Open
↓
Closed
0
↓
Battery voltage
ALKIA1708ZZ
2011 Pathfinder
DLK-232
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
GLASS HATCH AJAR SWITCH
4. Check continuity between BCM connector (A) M19 terminal 42
and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK GLASS HATCH AJAR SWITCH
Check continuity between glass hatch ajar switch connector terminal 1 and ground.
Is the inspection result normal?
YES
>> Refer to
GI-37, "Intermittent Incident"
.
NO
>> Replace glass hatch ajar switch.
42 - 1
:Continuity should exist
42 - Ground
:Continuity should not exist
ALKIA1709ZZ
Terminals
Condition
Continuity
Glass hatch ajar
switch
1 – Ground
Open
Yes
Closed
No
ALKIA0668ZZ
2011 Pathfinder
DOOR LOCK AND UNLOCK SWITCH
DLK-233
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK AND UNLOCK SWITCH
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000006245615
Transmits door lock/unlock operation to BCM.
DRIVER SIDE : Component Function Check
INFOID:0000000006245616
1.
CHECK FUNCTION
With CONSULT-III
Check CDL LOCK SW, CDL UNLOCK SW in Data Monitor mode with CONSULT-III.
Is the inspection result normal?
YES
>> Door lock and unlock switch is OK.
NO
>> refer to
DLK-233, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000006245617
Regarding Wiring Diagram information, refer to
DLK-279, "Wiring Diagram - Without Intelligent Key System"
1.
CHECK DOOR LOCK/UNLOCK SWITCH INPUT SIGNAL
With CONSULT-III
Check main power window and door lock/unlock switch ("CDL LOCK SW", "CDL UNLOCK SW") in DATA
MONITOR mode in CONSULT–III.
• When main power window and door lock/unlock switch is turned to LOCK:
• When main power window and door lock/unlock switch is turned to UNLOCK:
Without CONSULT-III
1. Remove key from ignition key cylinder.
2. Using an oscilloscope, check the signal between BCM connector M18 terminal 22 and ground when the
main power window and door lock/unlock switch is turned to LOCK or UNLOCK.
3. Make sure the signals which are shown in the figure below can be detected during 10 seconds just after
the door lock/unlock switch is turned to LOCK or UNLOCK.
Monitor item
Condition
CDL LOCK SW
LOCK
: ON
UNLOCK
: OFF
CDL UNLOCK SW
LOCK
: OFF
UNLOCK
: ON
CDL LOCK SW
:ON
CDL UNLOCK SW
:ON
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст