Nissan Pathfinder (2011 year). Manual — part 255
EC-94
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000006243774
1.
INSPECTION START
Start engine.
Is engine running?
Yes or No
Yes
>> GO TO 8.
No
>> GO TO 2.
2.
CHECK ECM POWER SUPPLY CIRCUIT-I
1. Turn ignition switch OFF and then ON.
2. Check voltage between ECM terminal 109 and ground with
CONSULT-III or tester.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors M31, E152
• Fuse block (J/B) connector M4
• 10 A fuse (No.1)
• Harness for open or short between ECM and fuse
>> Repair harness or connectors.
4.
CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Loosen and retighten three ground screws on the body. Refer to
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace ground connections.
5.
CHECK ECM GROUND CIRCUIT FOR OPEN AND SHORT-I
1. Disconnect ECM harness connector.
2. Check harness continuity between ECM terminals 1, 115, 116 and ground.
Refer to Wiring Diagram.
Voltage: Battery voltage
MBIB0015E
BBIA0539E
Continuity should exist.
2011 Pathfinder
POWER SUPPLY AND GROUND CIRCUIT
EC-95
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3. Also check harness for short to power.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F32, E2
• Harness for open or short between ECM and ground
>> Repair open circuit or short to power in harness or connectors.
7.
CHECK ECM POWER SUPPLY CIRCUIT-II
1. Reconnect ECM harness connector.
2. Turn ignition switch ON.
3. Check voltage between IPDM E/R connector E119 terminal 3
and ground with CONSULT-III or tester.
OK or NG
OK
>> Go to
NG
>> GO TO 8.
8.
CHECK ECM POWER SUPPLY CIRCUIT-III
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON and then OFF.
3. Check voltage between ECM terminals 119, 120 and ground
with CONSULT-III or tester.
OK or NG
OK
>> GO TO 13.
NG (Battery voltage does not exist.)>>GO TO 9.
NG (Battery voltage exists for more than a few seconds.)>>GO TO
11.
9.
CHECK ECM POWER SUPPLY CIRCUIT-IV
Check voltage between ECM terminal 111 and ground with CON-
SULT-III or tester.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 11.
10.
CHECK ECM POWER SUPPLY CIRCUIT-V
1. Disconnect ECM harness connector.
2. Disconnect IPDM E/R harness connector E119.
Voltage: Battery voltage
PBIB2569E
Voltage:
After turning ignition switch OFF, battery
voltage will exist for a few seconds, then to
drop approximately 0V.
PBIB1630E
Voltage: Battery voltage
PBIB1191E
2011 Pathfinder
EC-96
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE]
POWER SUPPLY AND GROUND CIRCUIT
3. Check harness continuity between ECM terminals 119, 120 and IPDM E/R terminal 4.
Refer to Wiring Diagram.
4. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 16.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
11.
CHECK ECM POWER SUPPLY CIRCUIT-VI
1. Disconnect ECM harness connector.
2. Disconnect IPDM E/R harness connector E119.
3. Check harness continuity between ECM terminal 111 and IPDM E/R terminal 7.
Refer to Wiring Diagram.
4. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 12.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
12.
CHECK 20A FUSE
1. Disconnect 20 A fuse (No.53) from IPDM E/R. For the fuse arrangement, refer to
.
2. Check 20 A fuse.
OK or NG
OK
>> GO TO 16.
NG
>> Replace 20A fuse.
13.
CHECK GROUND CONNECTIONS
Loosen and retighten three ground screws on the body. Refer to
.
OK or NG
OK
>> GO TO 14.
NG
>> Repair or replace ground connections.
14.
CHECK ECM GROUND CIRCUIT FOR OPEN AND SHORT-II
1. Check harness continuity between ECM terminals 1, 115, 116 and ground.
Refer to Wiring Diagram.
2. Also check harness for short to power.
OK or NG
OK
>> GO TO 16.
NG
>> GO TO 15.
15.
DETECT MALFUNCTIONING PART
Check the following.
Continuity should exist.
Continuity should exist.
BBIA0539E
Continuity should exist.
2011 Pathfinder
POWER SUPPLY AND GROUND CIRCUIT
EC-97
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
• Harness connectors F32, E2
• Harness for open or short between ECM and ground
>> Repair open circuit or short to power in harness or connectors.
16.
CHECK INTERMITTENT INCIDENT
GI-37, "Intermittent Incident"
.
OK or NG
OK
>> Replace IPDM E/R. Refer to
PCS-29, "Removal and Installation of IPDM E/R"
.
NG
>> Repair open circuit or short to power in harness or connectors.
Ground Inspection
INFOID:0000000006243775
Ground connections are very important to the proper operation of electrical and electronic circuits. Ground
connections are often exposed to moisture, dirt and other corrosive elements. The corrosion (rust) can
become an unwanted resistance. This unwanted resistance can change the way a circuit works.
Electronically controlled circuits are very sensitive to proper grounding. A loose or corroded ground can drasti-
cally affect an electronically controlled circuit. A poor or corroded ground can easily affect the circuit. Even
when the ground connection looks clean, there can be a thin film of rust on the surface.
When inspecting a ground connection follow these rules:
• Remove the ground bolt or screw.
• Inspect all mating surfaces for tarnish, dirt, rust, etc.
• Clean as required to assure good contact.
• Reinstall bolt or screw securely.
• Inspect for “add-on” accessories which may be interfering with the ground circuit.
• If several wires are crimped into one ground eyelet terminal, check for proper crimps. Make sure all of the
wires are clean, securely fastened and providing a good ground path. If multiple wires are cased in one eye-
let make sure no ground wires have excess wire insulation.
For detailed ground distribution information, refer to
.
PBIB1870E
2011 Pathfinder
EC-98
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE]
U0101 CAN COMM CIRCUIT
U0101 CAN COMM CIRCUIT
Description
INFOID:0000000006243776
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
On Board Diagnosis Logic
INFOID:0000000006243777
This self-diagnosis has the one trip detection logic.
DTC Confirmation Procedure
INFOID:0000000006243778
1. Turn ignition switch ON and wait at least 3 seconds.
2. Check 1st trip DTC.
3. If 1st trip DTC is detected, go to
.
Diagnosis Procedure
INFOID:0000000006243779
Go to
LAN-52, "CAN System Specification Chart"
.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
U0101
0101
Lost communication
with TCM
• When ECM is not transmitting or receiving
CAN communication signal of OBD (emission-
related diagnosis) with TCM for 2 seconds or
more.
• CAN communication line between TCM
and ECM
• CAN communication line is open or short-
ed
2011 Pathfinder
U1001 CAN COMM CIRCUIT
EC-99
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
U1001 CAN COMM CIRCUIT
Description
INFOID:0000000006243780
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
On Board Diagnosis Logic
INFOID:0000000006243781
The MIL will not illuminate for this diagnosis.
DTC Confirmation Procedure
INFOID:0000000006243782
1. Turn ignition switch ON and wait at least 3 seconds.
2. Check 1st trip DTC.
3. If 1st trip DTC is detected, go to
.
Diagnosis Procedure
INFOID:0000000006243783
Go to
LAN-52, "CAN System Specification Chart"
.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
U1001
1001
CAN communication
line
• When ECM is not transmitting or receiving
CAN communication signal other than OBD
(emission-related diagnosis) for 2 seconds or
more.
• Harness or connectors
(CAN communication line is open or
shorted)
2011 Pathfinder
EC-100
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE]
P0011, P0021 IVT CONTROL
P0011, P0021 IVT CONTROL
On Board Diagnosis Logic
INFOID:0000000006243784
FAIL-SAFE MODE
When the malfunction is detected, the ECM enters fail-safe mode.
DTC Confirmation Procedure
INFOID:0000000006243785
CAUTION:
Always drive at a safe speed.
NOTE:
•
If DTC P0011 or P0021 is displayed with DTC P0075 or P0081, first perform trouble diagnosis for DTC
P0075 or P0081. Refer to
.
• If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next step.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is between 10V and 16V at
idle.
WITH CONSULT-III
1. Turn ignition switch ON and select “DATA MONITOR” mode with CONSULT-III.
2. Start engine and warm it up to the normal operating temperature.
3. Maintain the following conditions for at least 6 consecutive seconds. Hold the accelerator pedal as steady
as possible.
4. Stop vehicle with engine running and let engine idle for 10 seconds.
5. Check 1st trip DTC.
6. If the 1st trip DTC is detected, go to
If the 1st trip DTC is not detected, go to next step.
7. Maintain the following conditions for at least 20 consecutive seconds.
DTC No.
Trouble diagnosis
name
Detecting condition
Possible cause
P0011
0011
(Bank 1)
Intake valve timing
control performance
There is a gap between angle of target and
phase-control angle degree.
• Crankshaft position sensor (POS)
• Camshaft position sensor (PHASE)
• Intake valve timing control solenoid valve
• Accumulation of debris to the signal pick-up
portion of the camshaft
• Timing chain installation
• Foreign matter caught in the oil groove for in-
take valve timing control
P0021
0021
(Bank 2)
Detected items
Engine operating condition in fail-safe mode
Intake valve timing control
The signal is not energized to the solenoid valve and the valve control does not function.
ENG SPEED
1,200 - 2,000 rpm
COOLAN TEMP/S
More than 60
°
C (140
°
F)
B/FUEL SCHDL
More than 3.5 msec
Selector lever
P or N position
ENG SPEED
1,700 - 3,175 rpm (A constant rotation is maintained.)
COOLAN TEMP/S
More than 70
°
C (158
°
F)
2011 Pathfinder
P0011, P0021 IVT CONTROL
EC-101
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
8. Check 1st trip DTC.
9. If the 1st trip DTC is detected, go to
.
WITH GST
Follow the procedure “WITH CONSULT-III” above.
Diagnosis Procedure
INFOID:0000000006243786
1.
CHECK OIL PRESSURE WARNING LAMP
1. Start engine.
2. Check oil pressure warning lamp and confirm it is not illumi-
nated.
OK or NG
OK
>> GO TO 2.
KG
>> Go to
.
2.
CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE
EC-102, "Component Inspection"
OK or NG
OK
>> GO TO 3.
NG
>> Replace malfunctioning intake valve timing control solenoid valve. Refer to
.
3.
CHECK CRANKSHAFT POSITION SENSOR (POS)
EC-221, "Component Inspection"
OK or NG
OK
>> GO TO 4.
NG
>> Replace crankshaft position sensor (POS). Refer to
4.
CHECK CAMSHAFT POSITION SENSOR (PHASE)
EC-226, "Component Inspection"
OK or NG
OK
>> GO TO 5.
NG
>> Replace malfunctioning camshaft position sensor (PHASE). Refer to
5.
CHECK CAMSHAFT (INTAKE)
Check the following.
• Accumulation of debris on the signal plate of camshaft rear end
• Chipping signal plate of camshaft rear end
OK or NG
OK
>> GO TO 6.
NG
>> Remove debris and clean the signal plate of camshaft
rear end or replace camshaft. Refer to
.
Selector lever
1st or 2nd position
Driving location uphill
Driving vehicle uphill
(Increased engine load will help maintain the driving
conditions required for this test.)
PBIA8559J
SEC905C
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст