Nissan Pathfinder (2011 year). Manual — part 316
EC-582
< WIRING DIAGRAM >
[VK56DE]
ENGINE CONTROL SYSTEM
ABBIA0440GB
2011 Pathfinder
DIAGNOSIS AND REPAIR WORK FLOW
EC-583
< BASIC INSPECTION >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Trouble Diagnosis Introduction
INFOID:0000000006244205
INTRODUCTION
The engine has an ECM to control major systems such as fuel con-
trol, ignition control, idle air control system, etc. The ECM accepts
input signals from sensors and instantly drives actuators. It is essen-
tial that both input and output signals are proper and stable. At the
same time, it is important that there are no malfunctions such as vac-
uum leakage, fouled spark plugs, or other malfunctions with the
engine.
It is much more difficult to diagnose an incident that occurs intermit-
tently rather than continuously. Most intermittent incidents are
caused by poor electric connections or improper wiring. In this case,
careful checking of suspected circuits may help prevent the replace-
ment of good parts.
A visual check only may not find the cause of the incidents. A road
test with CONSULT-III (or GST) or a circuit tester connected should
be performed. Follow the Work Flow on "WORK FLOW".
Before undertaking actual checks, take a few minutes to talk with a
customer who approaches with a driveability complaint. The cus-
tomer can supply good information about such incidents, especially
intermittent ones. Find out what symptoms are present and under
what conditions they occur. A Diagnostic Worksheet like the example
on "Worksheet Sample" should be used.
Start your diagnosis by looking for conventional malfunctions first.
This will help troubleshoot driveability malfunctions on an electroni-
cally controlled engine vehicle.
WORK FLOW
MEF036D
SEF233G
SEF234G
2011 Pathfinder
EC-584
< BASIC INSPECTION >
[VK56DE]
DIAGNOSIS AND REPAIR WORK FLOW
Overall Sequence
Detailed Flow
1.
GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred) using the DIAGNOSTIC WORKSHEET.
>> GO TO 2.
JMBIA1416GB
2011 Pathfinder
DIAGNOSIS AND REPAIR WORK FLOW
EC-585
< BASIC INSPECTION >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is displayed.
-
Record DTC and freeze frame data. (Print them out with CONSULT-III or GST.)
-
Erase DTC. (Refer to
EC-530, "CONSULT-III Function"
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
(Symptom Matrix Chart is useful. Refer to
EC-933, "Symptom Matrix Chart"
3. Check related service bulletins for information.
Are any symptoms described and any DTCs detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer (except MIL ON).
DIAGNOSIS WORKSHEET is useful to verify the incident.
Also study the normal operation and fail-safe related to the symptom. Refer to
No Load and High Engine Speed)"
.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
DIAGNOSIS WORK SHEET is useful to verify the incident.
Also study the normal operation and fail-safe related to the symptom. Refer to
No Load and High Engine Speed)"
.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
If two or more DTCs are detected, refer to
EC-551, "DTC Inspection Priority Chart"
diagnosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Overall Function Check if DTC Confirmation Procedure is not included on Service Manual. This
simplified check procedure is an effective alternative though DTC cannot be detected during this check.
If the result of Overall Function Check is NG, it is the same as the detection of DTC by DTC Confirmation
Procedure.
Is DTC detected?
Yes
>> GO TO 10.
No
>> Check according to WORK FLOW.
6.
PERFORM BASIC INSPECTION
Perform
With CONSULT-III>>GO TO 7.
Without CONSULT-III>>GO TO 9.
7.
PERFORM SPEC IN DATA MONITOR MODE
With CONSULT-III
Check that “MAS A/F SE-B1”, “B/FUEL SCHDL”, and “A/F ALPHA-B1”, “A/F ALPHA-B2” are within the SP
value using CONSULT-III “SPEC” in “DATA MONITOR” mode. Refer to
EC-601, "Inspection Procedure"
.
Are they within the SP value?
Yes
>> GO TO 9.
2011 Pathfinder
EC-586
< BASIC INSPECTION >
[VK56DE]
DIAGNOSIS AND REPAIR WORK FLOW
No
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART BY TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Detect malfunctioning part according to
.
Is a malfunctioning part detected?
Yes
>> GO TO 11.
No
>> GO TO 9.
9.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM MATRIX CHART
Detect malfunctioning system according to
EC-933, "Symptom Matrix Chart"
based on the confirmed symptom
in step 4, and determine the trouble diagnosis order based on possible causes and symptoms.
>> GO TO 10.
10.
DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure in EC section described based on open circuit inspection. A short circuit inspection
is also required for the circuit check in the Diagnostic Procedure. For details, refer to Circuit Inspection in
Is a malfunctioning part detected?
Yes
>> GO TO 11.
No
>> Monitor input data from related sensors using CONSULT-III or check voltage of related ECM ter-
EC-538, "CONSULT-III Reference Value in Data Monitor Mode"
11.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is displayed, erase it, refer to
EC-530, "CONSULT-III Function"
>> GO TO 12.
12.
FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Overall Function Check again,
and then check that the malfunction have been completely repaired.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
OK or NG
NG (DTC is detected)>>GO TO 10.
NG (Symptom remains)>>GO TO 6.
OK
>> 1. Before returning the vehicle to the customer, always erase unnecessary DTC in ECM and
EC-530, "CONSULT-III Function"
TM-34, "OBD-II Diagnostic Trouble
.)
2. If the completion of SRT is needed, drive vehicle under the specific driving pattern. Refer to
Driving Pattern in
EC-525, "DIAGNOSIS DESCRIPTION : Driving Pattern"
3. INSPECTION END
DIAGNOSTIC WORKSHEET
Description
2011 Pathfinder
DIAGNOSIS AND REPAIR WORK FLOW
EC-587
< BASIC INSPECTION >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
There are many operating conditions that lead to the malfunction of
engine components. A good grasp of such conditions can make trou-
bleshooting faster and more accurate.
In general, each customer feels differently about symptoms. It is
important to fully understand the symptoms or conditions for a cus-
tomer complaint.
Utilize a diagnostic worksheet like the Worksheet Sample below in
order to organize all the information for troubleshooting.
Some conditions may cause the MIL to illuminate or blink, and DTC
to be detected. Examples:
• Vehicle ran out of fuel, which caused the engine to misfire.
• Fuel filler cap was left off or incorrectly screwed on, allowing fuel to
evaporate into the atmosphere.
Worksheet Sample
SEF907L
MTBL0017
2011 Pathfinder
EC-588
< BASIC INSPECTION >
[VK56DE]
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
Basic Inspection
INFOID:0000000006244206
1.
INSPECTION START
1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for
scheduled maintenance.
2. Open engine hood and check the following:
-
Harness connectors for improper connections
-
Wiring harness for improper connections, pinches and cut
-
Vacuum hoses for splits, kinks and improper connections
-
Hoses and ducts for leakage
-
Air cleaner clogging
-
Gasket
3. Check that electrical or mechanical loads are not applied.
-
Headlamp switch is OFF.
-
Air conditioner switch is OFF.
-
Rear window defogger switch is OFF.
-
Steering wheel is in the straight-ahead position, etc.
4. Start engine and warm it up until engine coolant temperature
indicator points to the middle of gauge.
Check that engine stays below 1,000 rpm.
5. Run engine at approximately 2,000 rpm for approximately 2 min-
utes under no load.
6. Check that no DTC is displayed with CONSULT-III or GST.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>> GO TO 3.
3.
CHECK TARGET IDLE SPEED
With CONSULT-III
1. Run engine at approximately 2,000 rpm for approximately 2 minutes under no load.
SEF983U
SEF976U
SEF977U
2011 Pathfinder
INSPECTION AND ADJUSTMENT
EC-589
< BASIC INSPECTION >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2. Rev engine between 2,000 and 3,000 rpm 2 or 3 times under no
load, then run engine at idle speed for approximately 1 minute.
3. Read idle speed in “DATA MONITOR” mode with CONSULT-III.
EC-592, "Idle Speed and Ignition Timing Check"
Without CONSULT-III
1. Run engine at approximately 2,000 rpm for approximately 2 minutes under no load.
2. Rev engine between 2,000 and 3,000 rpm 2 or 3 times under no load, then run engine at idle speed for
approximately 1 minute.
3. Check idle speed.
EC-592, "Idle Speed and Ignition Timing Check"
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 4.
4.
PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1. Stop engine.
2. Perform
EC-593, "Accelerator Pedal Released Position Learning"
.
>> GO TO 5.
5.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform
EC-593, "Throttle Valve Closed Position Learning"
.
>> GO TO 6.
6.
PERFORM IDLE AIR VOLUME LEARNING
EC-593, "Idle Air Volume Learning"
Is Idle Air Volume Learning carried out successfully?
Yes or No
Yes
>> GO TO 7.
No
>> 1. Follow the instructions of Idle Air Volume Learning.
2. GO TO 4.
7.
CHECK TARGET IDLE SPEED AGAIN
With CONSULT-III
1. Start engine and warm it up to normal operating temperature.
2. Read idle speed in “DATA MONITOR” mode with CONSULT-III.
EC-592, "Idle Speed and Ignition Timing Check"
Without CONSULT-III
1. Start engine and warm it up to normal operating temperature.
2. Check idle speed.
EC-592, "Idle Speed and Ignition Timing Check"
OK or NG
650
±
50 rpm (in P or N position)
PBIA8513J
650
±
50 rpm (in P or N position)
650
±
50 rpm (in P or N position)
650
±
50 rpm (in P or N position)
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст