Nissan Pathfinder (2011 year). Manual — part 494
DOOR MIRROR
MIR-17
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
• Pull from the bottom to disengage the clips.
• Continue to pivot the mirror upward from the bottom to separate the hooks.
3. Disconnect the harness connectors and remove the mirror glass.
INSTALLATION
Installation is in the reverse order of removal.
2011 Pathfinder
MIR-18
< UNIT DISASSEMBLY AND ASSEMBLY >
DOOR MIRROR
UNIT DISASSEMBLY AND ASSEMBLY
DOOR MIRROR
Mirror Actuator
INFOID:0000000006243550
DISASSEMBLY AND ASSEMBLY
Disassembly
1. Remove the mirror glass. Refer to
.
2. Remove the screws (A) and release the actuator from housing
(B).
3. Disconnect the connectors (A) and remove the actuator (1).
Assembly
Assembly is the reverse order of disassembly.
ALIIA0357GB
ALIIA0358GB
2011 Pathfinder
PB-1
BRAKES
C
D
E
G
H
I
J
K
L
M
SECTION
PB
A
B
PB
N
O
P
CONTENTS
PARKING BRAKE SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
PARKING BRAKE SYSTEM . . . . . . . ...
On-Vehicle Service . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . .
PARKING BRAKE CONTROL . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
PARKING BRAKE SHOE . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Parking Drum Brake . . . . . . . . . . . .
Parking Brake Control . . . . . . . . . . . .
2011 Pathfinder
PB-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006245766
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000006245767
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
2011 Pathfinder
PRECAUTIONS
PB-3
< PRECAUTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
2011 Pathfinder
PB-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000006245768
(Kent-Moore No.)
Tool name
Description
(J-21177-A)
Brake drum clearance gauge
Measuring rear rotor drum inner diameter
Power tool
Loosening nuts, screws and bolts
WFIA0167E
PIIB1407E
2011 Pathfinder
PARKING BRAKE SYSTEM
PB-5
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PERIODIC MAINTENANCE
PARKING BRAKE SYSTEM
On-Vehicle Service
INFOID:0000000006245769
PEDAL STROKE
• When parking brake pedal is operated with the specified force, make sure the stroke is within the specified
number of notches. Check by listening and counting the ratchet clicks.
INSPECTION
• Make sure the components are attached properly, checking for looseness or backlash.
• Check parking brake pedal assembly for bends, damage and cracks, and replace if necessary.
• Check cable for wear and damage, and replace if necessary.
• Check parking brake warning lamp switch for malfunction, and replace if necessary. Refer to
.
ADJUSTMENT
1. Remove instrument lower panel LH. Refer to
IP-14, "Removal and Installation"
2. Partially engage parking brake pedal to access adjusting nut.
3. Insert a deep socket wrench to rotate adjusting nut and loosen
cable until tension is sufficiently released. Then, disengage the
parking brake pedal.
4. Remove the rear wheel and tire using power tools. Refer to
.
5. Using wheel nuts, secure the disc to the hub to prevent it from tilting.
6. Remove the adjuster hole plug installed on the disc rotor. Turn
the adjuster (1) in direction (A) using a suitable tool or flat-
bladed screw driver as shown, until disc rotor is locked. Turn the
adjuster in the opposite direction by 5 or 6 notches after locking.
7. Rotate disc rotor to make sure there is no drag.
8. Adjust cable as follows:
a. If parking brake cable was replaced, operate parking brake
pedal 10 or more times with a full stroke of 232.2 mm (9.14 in).
b. Rotate the adjustment nut to adjust parking brake pedal operat-
ing force to 196 N-f (20.0 kg-f, 44.1 lb-f) under a pedal stroke
within the specified number of notches.
c. Release the parking brake pedal and rotate the disc rotor to make sure there is no drag.
Number of notches
: Refer to
PB-11, "Parking Brake Control"
.
WFIA0165E
Number of notches
: Refer to
PB-11, "Parking Brake Control"
.
ALFIA0172GB
2011 Pathfinder
PB-6
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
REMOVAL AND INSTALLATION
PARKING BRAKE CONTROL
Exploded View
INFOID:0000000006245770
Removal and Installation
INFOID:0000000006245771
REMOVAL
1. Remove the instrument lower panel LH and center console. Refer to
IP-14, "Removal and Installation"
(instrument panel) and
IP-21, "Removal and Installation"
(center console).
2. Remove the front floor trim. Refer to
INT-21, "Removal and Installation"
.
1.
Lock plate
2.
Pedal assembly
3.
Adjusting nut
4.
Left rear cable
5.
Right rear cable
6.
Pin
7.
Return spring
8.
Equalizer
9.
Front cable grommet
10. Front cable
A.
Attached to steering member stay
Front
AWFIA0477GB
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст