Nissan Pathfinder (2011 year). Manual — part 534
SE-30
< REMOVAL AND INSTALLATION >
FRONT SEAT
1.
Headrest
2.
Seatback assembly
3.
Headrest holder
4.
Headrest holder with multi position
lock
5.
Seatback board
6.
Power seat cushion rear finisher
7.
Leg Cover
8.
Lifter motor link bar
9.
Seat belt buckle assembly
10. Seat cushion inner finisher
11. Seat frame assembly
12. Seat lifter motor assembly
13. Seat spacer
14. Lock gear
15. Seat cushion front finisher
16. Flexible seat wire
17. Front seat slide motor assembly
18. Power seat control assembly
19. Lifter motor bracket assembly
20. Driver seat wiring harness
21. Seat cushion outer finisher
22 Leg cover
23 Bolt cover
24. Seat cushion frame
25. Recliner switch knob
26. Slide switch knob
27. Power seat switch escutcheon
28. Switch assembly
29. Seat cushion pad
30. Seat cushion heating element
31. Seat cushion trim
32. Seat cushion assembly
33. Lumbar support lever knob
34. Snap ring
2011 Pathfinder
FRONT SEAT
SE-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Manual Driver Seat
AWJIA0551ZZ
1.
Headrest
2.
Trim clip
3.
Seatback assembly
4.
Seat cushion trim cover
5.
Seat cushion pad
6.
Snap ring
7.
Seat cushion frame
8.
Seat cushion inner finisher
9.
Seat belt buckle assembly
10. Seat frame assembly
11. Leg cover
12. Bolt cover
13. Recline lever
14. Seat cushion outer finisher
15. Leg cover
16. Seat cushion rear finisher
17. Seat cushion lift knobs
18. Seatback board
2011 Pathfinder
SE-32
< REMOVAL AND INSTALLATION >
FRONT SEAT
Conventional Passenger Seat
19. Headrest holder with multi position
lock
20. Headrest holder
21. Lumbar support lever knob
22. Snap ring
AWJIA0552ZZ
1.
Damper assembly
2.
Headrest
3.
Seatback assembly
4.
Switch assembly
5.
Power seat switch escutcheon
6.
Recliner switch knob
7.
Slide switch knob
8.
Seat cushion assembly
9.
Seat cushion outer cover
10. Leg cover
11. Seat cushion front finisher
12. Passenger seat wiring harness
13. Power seat frame assembly
14. Seat cushion inner finisher
15. Seat belt buckle assembly
16. Leg cover
17. Seat cushion rear finisher
18. Manual seat frame assembly
19. Recline lever
20. Seat cushion rear finisher
21. Seatback board
2011 Pathfinder
FRONT SEAT
SE-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Fold Flat Passenger Seat
Removal and Installation
INFOID:0000000006247159
REMOVAL
22. Headrest holder with multi position
lock
23. Headrest holder
AWJIA0553ZZ
1.
Front seatback lever
2.
Trim clip
3.
Headrest
4.
Seatback assembly
5.
Seat cushion assembly
6.
Seat cushion outer finisher
7.
Leg cover
8.
Seat frame assembly
9.
Passenger seat wiring harness
10. Seat cushion inner cover
11. Leg cover
12. Seat belt buckle assembly
13. Inboard reclining arm outer cover
14. Inboard reclining arm inner cover
15. Outboard reclining arm inner cover
16. Outboard reclining arm outer cover
17. Seat cushion rear finisher
18. Seatback board
19. Headrest holder with multi position
lock
20. Headrest holder
2011 Pathfinder
SE-34
< REMOVAL AND INSTALLATION >
FRONT SEAT
CAUTION:
• When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.
• Before removing the front seat, turn the ignition switch off, disconnect both battery terminals and
wait at least 3 minutes.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After front side air bag module inflates, front seatback assembly must be replaced.
• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-
ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect
the Occupant Classification System calibration.
• Always replace passenger seat cushion as an assembly.
1. Slide the seat until the four mounting bolts are visible and a tool can be inserted.
NOTE:
Set the front/rear cushion lifters to the top position.
2. Disconnect both the negative and positive battery terminals and wait at least 3 minutes.
3. Disconnect the side air bag module harness connector.
4. If removing the passenger seat, disconnect the Occupant Classification System harness.
5. Remove the four mounting bolts.
6. Disconnect the power seat harness connectors (if equipped) and remove the seat from the vehicle.
CAUTION:
When removing and installing the seat, use shop cloths to protect the vehicle from damage.
INSTALLATION
Installation is in the reverse order of removal.
2011 Pathfinder
REAR SEAT
SE-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REAR SEAT
Removal and Installation
INFOID:0000000006247160
Second Row Outboard
Removal
1. Tilt seat cushion forward.
2. Remove two seat bolts.
3. Lower seat cushion and tilt seatback forward.
4. Remove seat base trim cover.
5. Remove forward seat nuts and assembly.
Installation
Installation is in the reverse order of removal.
Second Row Center
Removal
1. Tilt the seat cushion forward.
2. Remove the seat cushion bolts and assembly.
3. Remove the seatback bolts and assembly.
Installation
Installation is in the reverse order of removal.
Third Row
Removal
1. Remove the lower base trim covers.
2. Remove front anchor bolts.
3. Lower the seatback into the cargo floor position.
4. Remove the rear anchor bolts from the seat assembly.
5. Remove the seat assembly.
ALJIA0226GB
AWIIA0113ZZ
WIIA0764E
2011 Pathfinder
SE-36
< REMOVAL AND INSTALLATION >
REAR SEAT
Installation
Installation is in the reverse order of removal.
2011 Pathfinder
FRONT SEAT
SE-37
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
FRONT SEAT
Exploded View
INFOID:0000000006247161
Power Driver Seat
AWJIA0550ZZ
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст