Qashqai J11. SRS airbag — part 2
SPIRAL CABLE
SR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SPIRAL CABLE
Exploded View
INFOID:0000000010478319
Removal and Installation
INFOID:0000000010478320
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove the steering wheel. Refer to
ST-8, "Removal and Installation"
2.
Remove the steering column upper and lower cover. Refer to
.
3.
Disconnect harness connectors (A).
4.
Remove screws (A) and then remove spiral cable (1).
CAUTION:
ALHIA0359ZZ
1.
Combination switch
2.
Steering angle sensor
3.
Spiral cable
ALHIA0351ZZ
ALHIA0350ZZ
SR-18
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
• Never impact the spiral cable.
• Replace the spiral cable if it has been dropped or sus-
tained an impact.
• Never disassemble the spiral cable.
• Never apply lubricant to the spiral cable.
• Never allow oil, grease, detergent, or water to come in
contact with the spiral cable.
INSTALLATION
Installation is in the reverse order of removal.
• The turn signal lever must be in the neutral position for spiral cable installation.
• Set the spiral cable neutral position by carefully turning the spiral
cable clockwise to the end position. Turn the spiral cable counter-
clockwise 2.5 turns stopping when the locating pin (B) is at the top
most position and confirm that a yellow indicator with a vertical
black line will be shown in the window (A).
NOTE:
If a new service part is installed, the neutral position is already set
with a stopper clip in place and should not be adjusted after the
stopper clip is removed. Make sure the stopper is removed before
installing the steering wheel.
• During steering wheel installation, make sure the locating pin hole
is aligned with the locating pin (B) of the spiral cable.
• Adjust the neutral position of the steering angle sensor. Refer to
CAUTION:
• The spiral cable may snap during steering operation if the spiral cable is installed in an improper
position.
• Never over turn the spiral cable or go beyond the maximum number of turns required. (This will
cause the cable to snap.)
• The turn signal lever must be in the neutral position for spiral cable installation.
• Never apply lubricant to the spiral cable.
• Never allow oil, grease, detergent or water to come in contact with the spiral cable.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• If a malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
JMHIA0009ZZ
ALHIA0385ZZ
PASSENGER AIR BAG MODULE
SR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000010478321
Removal and Installation
INFOID:0000000010478322
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove the Instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Remove front passenger air bag module screws.
3.
Release the pawls by removing the front passenger air bag module.
CAUTION:
• Always place the front passenger air bag module with pad
side facing upward as shown.
: Upward
E1HIA0039GB
1.
Front passenger air bag module 2.
Steering member
A.
To instrument panel
Refer to
for symbols in the figure.
ALHIA0387ZZ
SR-20
< REMOVAL AND INSTALLATION >
PASSENGER AIR BAG MODULE
• Replace the front passenger air bag module if it has been
dropped or sustained an impact.
• Never impact the front passenger air bag module.
• Never insert any foreign objects (screwdriver, etc.) into the passenger air bag module.
• Never disassemble the passenger air bag module.
• Never expose the passenger air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the front passenger air bag mod-
ule.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old fixing bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• If a malfunction is indicated by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
JMHIA0009ZZ
CURTAIN AIR BAG MODULE
SR-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000010478323
Removal and Installation
INFOID:0000000010478324
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminals and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove the headlining. Refer to
INT-25, "Removal and Installation"
.
2.
Disconnect the harness connector from the curtain air bag mod-
ule.
CAUTION:
• For removing/installing the curtain air bag module har-
ness connector, insert thin screwdriver wrapped in tape
into notch, lift lock and remove the connector.
• Install the connector with lock raised, and push lock into
the connector.
• After installing the connector, check that the lock is
pushed in securely into it.
3.
Remove bolts, and curtain air bag module.
CAUTION:
• Replace the curtain air bag module if it has been dropped or sustained an impact.
• Never impact the curtain air bag module.
E1HIA0040GB
1.
Side curtain air bag module
2.
Mounting clip
3.
Front pillar
4.
Trim clip
A.
No curtain airbag variant
Refer to
for symbols in the figure.
PHIA0953J
SR-22
< REMOVAL AND INSTALLATION >
CURTAIN AIR BAG MODULE
• Never insert any foreign objects (screwdriver, etc.) into the curtain air bag module.
• Never disassemble the curtain air bag module.
• Never expose the curtain air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent or water to come in contact with the curtain air bag module.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never damage the harness while installing.
• Make sure that the curtain air bag module bracket supporting hooks are securely seated into the
body slots before releasing the curtain air bag module during installation to avoid damaging the cur-
tain air bag module.
• Check perforation of curtain air bag module to check that curtain air bag module is not twisted.
• If a malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
SIDE AIR BAG MODULE
SR-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE AIR BAG MODULE
Removal and Installation
INFOID:0000000010478325
WARNING:
• Before servicing, turn ignition swith OFF, disconnect battery negative terminal and wait 3 minutes or
more.
• Always work from the rear of air bag module.
• Never use the air tools or electric tools for servicing.
The front side air bag module is part of the front seatback. For removal and installation of the front seatback,
refer to
SE-29, "SEATBACK : Disassembly and Assembly"
.
SR-24
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Exploded View
INFOID:0000000010478326
Removal and Installation
INFOID:0000000010478327
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove front grille. Refer to
EXT-25, "Removal and Installation"
2.
Remove crash zone sensor nut.
CAUTION:
Never reuse the crash zone sensor nut.
3.
Disconnect crash zone sensor harness connector, and remove crash zone sensor and bracket.
CAUTION:
• Replace the crash zone sensor if it has been dropped or sustained an impact.
• Never impact the crash zone sensor.
• Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger air
bag.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Never reuse the crash zone sensor nut.
• Never damage the harness while installing.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
E1HIA0041GB
1.
Upper center rad core support
assembly
2.
Crash zone sensor harness
connector
3.
Crash zone sensor
4.
Bracket
Refer to
for symbols in the figure.
CRASH ZONE SENSOR
SR-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• If a malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
SR-26
< REMOVAL AND INSTALLATION >
SATELLITE SENSOR
SATELLITE SENSOR
Exploded View
INFOID:0000000010478328
Removal and Installation
INFOID:0000000010478329
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use air tools or electric tools for servicing.
SATELLITE SENSOR
Removal
1.
Remove center pillar lower garnish. Refer to
INT-18, "Removal and Installation"
.
2.
Remove the satellite sensor nut.
CAUTION:
Never reuse the satellite sensor nut.
3.
Disconnect the harness connector from the satellite sensor.
4.
Remove satellite sensor.
CAUTION:
• Replace the satellite sensor if it has been dropped or sustained an impact.
• Never impact the satellite sensor.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
• Never reuse the satellite sensor nut.
• Never damage the harness while installing.
1.
Center pillar
2.
Satellite sensor
for symbols in the figure.
E1HIA0042GB
SATELLITE SENSOR
SR-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Never install normally aligning to the cutout hole, because performance of the satellite sensor
excessively fluctuates according to the installation position.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• If a malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
SR-28
< REMOVAL AND INSTALLATION >
DIAGNOSIS SENSOR UNIT
DIAGNOSIS SENSOR UNIT
Exploded View
INFOID:0000000010478330
Removal and Installation
INFOID:0000000010478331
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Before disconnecting the air bag diagnosis sensor unit harness connectors, be sure to disconnect
each harness connector of the air bag module and pre-tensioner seat belt to prevent air bag deploy-
ment by static electricity and pre-temsioner seat belt operation.
• Never use the air tools or electric tools for servicing.
• When replacing the air bag diagnosis sensor unit, always check with the parts department for the lat-
est parts information. Installing an incorrect air bag diagnosis sensor unit may or may not cause the
air bag warning lamp to illuminate and may cause incorrect deployment of the supplemental air bags
and seat belt pre-tensioners in a collision resulting in serious personal injury or death.
REMOVAL
1.
Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) using
CONSULT.
2.
Remove center console assembly. Refer to
IP-19, "Removal and Installation"
3.
Disconnect the harness connectors for the following SRS components:
SR-21, "Removal and Installation"
(curtain air bag modules),
SR-30, "Removal and Installation"
(front seat belt pre-tensioner) and
(front side air bag module).
4.
Disconnect the harness connectors from the diagnosis sensor unit.
5.
Remove bolt and nuts, then remove the air bag diagnosis sensor unit.
CAUTION:
• Never reuse the air bag diagnosis sensor unit bolts.
• Replace the air bag diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat
belt pre-tensioner.
AWHIA0599ZZ
1.
Diagnosis sensor unit
Refer to
for symbols in the figure.
DIAGNOSIS SENSOR UNIT
SR-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Replace the air bag diagnosis sensor unit if it has been
dropped or sustained an impact.
• Never impatc the air bag diagnosis sensor unit.
INSTALLATION
Install air bag diagnosis sensor unit in the reverse order of removal.
CAUTION:
• Never reuse the air bag diagnosis sensor unit bolts.
• The air bag diagnosis sensor unit must always be installed with the label arrow mark "
" pointing
toward the front of the vehicle for proper operation.
• Never damage the harness while installing.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• If a malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After replacing the air bag diagnosis sensor unit, confirm using CONSULT that the ECU discrimi-
nated number (identification number) of the new replacement air bag diagnosis sensor unit matches
the ECU discriminated number (identification number) of the replaced (old) air bag diagnosis sensor
unit.
NOTE:
If the ECU discriminated number of the new replacement air bag diagnosis sensor unit differs from the ECU
discriminated number of the replaced air bag diagnosis sensor unit, reconfirm the parts information and verify
that the correct air bag diagnosis sensor unit was installed.
SGI787
SR-30
< REMOVAL AND INSTALLATION >
SEAT BELT PRE-TENSIONER
SEAT BELT PRE-TENSIONER
Exploded View
INFOID:0000000010499319
Removal and Installation
INFOID:0000000010478332
For removal and installation procedures, refer to
SB-7, "SEAT BELT RETRACTOR : Removal and Installa-
.
DISPOSAL OF AIR BAG MODULE
SR-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
DISPOSAL OF AIR BAG MODULE
DRIVER AIR BAG MODULE
DRIVER AIR BAG MODULE : Deployment
INFOID:0000000010499321
CHECKING DEPLOYMENT TOOL
Connecting to Battery
CAUTION:
The battery must show voltage of 9.6 V or more.
Remove the battery from the vehicle and place it on dry wood blocks
approximately 5.0 m (16.4 ft) away from the vehicle.
• Wait 3 minutes after the vehicle battery is disconnected before pro-
ceeding.
• Connect red clip of deployment tool (A) to battery positive terminal
and black clip to negative terminal.
Check that the polarity is correct. The right side lamp in the
tool, marked “deployment tool power”, should illuminate with a
green light. If the right side lamp illuminates red, reverse the
connections to the battery.
Deployment Tool Check
Press the deployment tool switch (C) to the ON position. The left
side lamp in the tool, marked “air bag connector voltage” should illu-
minate (B). If it does not illuminate, replace the deployment tool (A).
Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)
*: If this lamp illuminates red, the tool is connected to the battery incorrectly. Reverse the connections and check that the lamp illumi-
nates green.
DEPLOYMENT OF DRIVER AIR BAG MODULE (OUTSIDE OF VEHICLE)
1.
Unless the vehicle is being scrapped, deploying the air bag in
the vehicle is not recommended. This may cause damage to the
vehicle interior.
Anchor air bag module bracket (SST: KV99105300) (A) in a vice
secured to a firm foundation deployment.
JMHIA0204ZZ
JMHIA0205ZZ
Switch operation
Left side lamp, green*
“AIR BAG CONNECTOR VOLTAGE”
Right side lamp, green*
“DEPLOYMENT TOOL POWER”
OFF
OFF
ON
ON
ON
ON
JMHIA0208ZZ
SR-32
< REMOVAL AND INSTALLATION >
DISPOSAL OF AIR BAG MODULE
2.
Using wire (D), secure driver air bag module (1) to air bag mod-
ule bracket (SST: KV99105300) (A) at two places.
CAUTION:
Use wire of at least 1.0 mm (0.039 in) diameter.
3.
Firmly secure air bag module bracket (SST: KV99105300) with
driver air bag module attached, in a vise.
4.
Connect deployment tool adapter (SST: KV99110500) yellow
connector (C) to driver air bag module and deployment tool con-
nector (SST: KV99106400) (B).
5.
Connect red clip of deployment tool (A) to battery positive termi-
nal and black clip to negative terminal (B).
6.
The lamp on the right side of the tool, marked “deployment tool
power”, should illuminate green, not red.
7.
Press the button on the deployment tool. The left side lamp on
the tool, marked “air bag connector voltage”, illuminates and the
air bag module (1) deploys.
CAUTION:
When deploying the driver air bag module, stand at least 5.0
m (16.4 ft) away from the air bag module.
DRIVER AIR BAG MODULE : Disposal
INFOID:0000000010499322
DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Deployed air bag module, seat belt pre-tensioner, and lap pre-tensioner are very hot. Before disposing of air
bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a
plastic bag before disposal.
CAUTION:
• Never apply water to a deployed air bag module or seat belt
pre-tensioner or lap pre-tensioner.
• Wear gloves when handling a deployed air bag module or seat
belt pre-tensioner or lap pre-tensioner.
• No poisonous gas is produced upon air bag module deploy-
ment. However, be careful not to inhale gas since it irritates
the throat and can cause choking.
• Never disassemble air bag module, seat belt pre-tensioner
and lap pre-tensioner.
• Air bag module, seat belt pre-tensioner and lap pre-tensioner
cannot be reused.
• Wash your hands clean after the work is complete.
PASSENGER AIR BAG MODULE
PASSENGER AIR BAG MODULE : Deployment
INFOID:0000000010499323
CHECKING DEPLOYMENT TOOL
Connecting to Battery
CAUTION:
JMHIA0630ZZ
JMHIA0209ZZ
SBF276H
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст