Nissan Xterra. Manual — part 585
FRONT SEAT
SE-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Locking headrest guide
2.
Headrest guide
3.
Headrest
4.
Seatback assembly with side air bag 5.
Lumbar support lever (if equipped)
6.
Seat cushion trim
7.
Seat cushion pad
8.
Seat cushion assembly
9.
Seat cushion frame
10. Seat cushion rear finisher
11. Leg cover
12. Seat belt buckle
13. Seat cushion inner finisher
14. Driver seat slide assembly
15. Seat cushion outer finisher
16. Seatback recline release lever
17. Outer pedestal finisher
18. Seat cushion adjusting knob clips (if
equipped)
19. Seat cushion adjusting knobs (if
equipped)
SE-20
< REMOVAL AND INSTALLATION >
FRONT SEAT
Passenger Seat
AWJIA1275ZZ
1.
Seatback board
2.
Locking headrest guide
3.
Headrest guide
4.
Headrest
5.
Front seatback lever (if equipped)
6.
Seat cushion assembly
7.
Seatback assembly with side air bag 8.
Fold flat seat frame slide assembly
9.
Inboard reclining arm outer cover
10. Inboard reclining arm inner cover
11. Outboard reclining arm inner cover
12. Outboard reclining arm outer cover
13. Seat cushion rear finisher
14. Fold flat seat frame
15. Seat cushion outer finisher
FRONT SEAT
SE-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Removal and Installation
INFOID:0000000009483053
SEAT ASSEMBLY
Removal
CAUTION:
• Before removing the front seat, turn the ignition switch off, disconnect both battery terminals and
wait at least three minutes.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After front side air bag module inflates, front seatback assembly must be replaced.
• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-
ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect
the Occupant Classification System calibration.
• Always replace passenger seat cushion as an assembly.
1. Position the seat until the three seat bolts and one nut are visible and a suitable tool can be inserted.
NOTE:
• If disassembling the seat after removal, set the front/rear cushion lifters to the top position (if equipped).
2. Disconnect the battery negative and positive terminals and wait at least three minutes. Refer to
3. Remove the three seat bolts and one nut.
4. Disconnect the harness connectors from the seat.
5. Remove the seat assembly from the vehicle.
CAUTION:
When removing and installing the seat, use shop cloths to protect the vehicle from damage.
Installation
Installation is in the reverse order of removal.
SEATBACK ASSEMBLY - DRIVER’S SEAT
Removal
1. Remove the driver’s seat assembly.
2. The seatback cover is attached with the following:
• Unzip the seatback trim flap (1)
• Unclip the lower retainer (2)
16. Outer pedestal finisher
17. Manual seat frame slide assembly
18. Seat cushion inner cover
19. Leg cover
20. Recline release lever
21. Bolt cap
LIIA2419E
SE-22
< REMOVAL AND INSTALLATION >
FRONT SEAT
3. Remove the four seatback bolts (two for each side) and the
seatback assembly.
Installation
Installation is in the reverse order of removal.
SEATBACK ASSEMBLY - PASSENGER’S SEAT, WITH SOFT SEATBACK
Removal
1. Remove the passenger seat assembly.
2. The seatback board is attached to the seat frame with the follow-
ing:
• Two top tabs (A)
• Two side tabs (B)
• Two bottom clips (C) (must be replaced)
3. Move seat to forward position.
4. Hold the seatback board as shown and pull the top of the seat-
back board away from the seatback frame.
5. Pull the middle part of the seatback board to disengage the side
tabs from the seatback frame.
6. Pull the lower part of the seatback board to disengage the bottom clips from the seatback frame.
LIIA2420E
ALIIA0366ZZ
ALIIA0368ZZ
ALIIA0367ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст