Nissan Xterra. Manual — part 78
BRAKE TUBE AND HOSE
BR-21
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE TUBE AND HOSE
Hydraulic Circuit
INFOID:0000000009484652
Type 1 and Type 2 - Four Channel Hydraulic System
AWFIA0789ZZ
1.
Actuator
2.
Master cylinder
3.
Brake booster
4.
Connector
5.
Axle mounted connector
9.3 N·m (0.95 kg-m, 82 in-lb)
A.
Union bolt (front caliper)
18.2 N·m (1.9 kg-m, 13 ft-lb)
B.
Flare nut M12
18.2 N·m (1.9 kg-m, 13 ft-lb)
C.
Flare nut M10
13.0 N·m (1.3 kg-m, 10 ft-lb)
D.
Flare nut M10
16.2 N·m (1.7 kg-m, 12 ft-lb)
E.
Flare nut M10
16.2 N·m (1.7 kg-m, 12 ft-lb)
F.
Hose connection (rear caliper)
18.2 N·m (1.9 kg-m, 13 ft-lb)
=
Hose
—
Tube
BR-22
< REMOVAL AND INSTALLATION >
BRAKE TUBE AND HOSE
Type 1 and Type 2
CAUTION:
• All hoses and piping (tubes) must be free from excessive bending, twisting and pulling.
• Make sure there is no interference with other parts when turning steering both clockwise and coun-
terclockwise.
• The brake piping is an important safety part. If a brake fluid leak is detected, always disassemble the
parts. Replace applicable part with a new one, if necessary.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend or twist brake hose sharply, or strongly pull it.
• When removing components, cover connections so that no dirt, dust, or other foreign matter gets in.
• Do not reuse drained brake fluid.
• After installation of the ABS actuator and electric unit (control unit), refill brake system with new
brake fluid. Then bleed the air from the system. Refer to
BR-17, "Bleeding Brake System"
.
Removal and Installation of Front Brake Piping and Brake Hose
INFOID:0000000009484653
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove front wheel and tire using power tool. Refer to
2. Remove reservoir cap.
AWFIA0743GB
1.
From master cylinder secondary side
18.2 N·m (1.9 kg-m, 13 ft-lb)
2.
To rear right disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
3.
To rear left disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
4.
To front right disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
5.
To front left disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
6.
From master cylinder primary side
18.2 N·m (1.9 kg-m, 13 ft-lb)
7.
ABS actuator and electric unit (control
unit)
8.
Harness connector
Front
BRAKE TUBE AND HOSE
BR-23
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
3. Remove brake tube from brake hose, using a suitable tool.
4. Remove lock plate and brake hose from bracket.
5. Remove union bolt and copper sealing washers, then remove
brake hose from caliper assembly.
CAUTION:
Do not reuse copper sealing washers.
INSTALLATION
1. Install brake hose by aligning with the protrusion on caliper
assembly, then install new copper sealing washers (1) and union
bolt (A). Tighten union bolt (A) to specified torque. Refer to
CAUTION:
Do not reuse copper sealing washers.
2. Insert brake hose end through bracket, then secure it to bracket
with lock plate.
3. Install brake tube to brake hose, then tighten flare nut to the
specified torque using a suitable tool. Refer to
4. Refill brake fluid and bleed brake system. Refer to
BR-17, "Bleeding Brake System"
.
5. Install the reservoir cap.
6. Install the front wheel and tire. Refer to
.
Removal and Installation of Rear Brake Piping and Brake Hose
INFOID:0000000009484654
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
LFIA0236E
LFIA0235E
AWFIA0795ZZ
LFIA0236E
BR-24
< REMOVAL AND INSTALLATION >
BRAKE TUBE AND HOSE
1. Remove rear wheel and tire using power tool. Refer to
.
2. Remove reservoir cap.
3. Remove brake tube from brake hose, using a suitable tool.
4. Remove lock plate and brake hose from bracket.
5. Remove the hose connection (A) and copper sealing washer
from caliper assembly.
CAUTION:
Do not reuse copper sealing washer.
INSTALLATION
1. Install the hose connection (A) with a new copper sealing
washer. Tighten the hose connection to the specified torque.
CAUTION:
Do not reuse copper sealing washer.
2. Insert brake hose end through bracket, then secure it to bracket
with lock plate.
3. Install brake tube to brake hose, then tighten flare nut to the
specified torque using a suitable tool.
4. Refill brake fluid and bleed brake system. Refer to
BR-17, "Bleeding Brake System"
.
5. Install the reservoir cap.
6. Install the rear wheel and tire. Refer to
Inspection After Installation
INFOID:0000000009484655
CAUTION:
LFIA0238E
ALFIA0167ZZ
ALFIA0167ZZ
LFIA0238E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст