Nissan Xterra. Manual — part 708
HEATER CORE
VTL-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
HEATER CORE
Component
INFOID:0000000009484339
Heater and Cooling Unit Assembly
Removal and Installation
INFOID:0000000009484340
HEATER CORE
Removal
1. Remove the heater and cooling unit assembly. Refer to
VTL-12, "Removal and Installation"
.
2. Remove the three heater core cover screws and the heater core cover.
3. Remove the heater core and evaporator pipe bracket.
4. Remove the heater core.
NOTE:
If the in-cabin microfilters are contaminated from coolant leaking from the heater core, replace the in-cabin
microfilters with new ones before installing the new heater core.
Installation
Installation is in the reverse order of removal.
LJIA0167E
1.
Heater core and evaporator pipe
bracket
2.
Heater core
3.
Heater and cooling unit assembly
4.
Heater core cover
VTL-18
< REMOVAL AND INSTALLATION >
INTAKE DOOR MOTOR
INTAKE DOOR MOTOR
Removal and Installation
INFOID:0000000009484341
Intake Door Motor - Heater and Cooling Unit Assembly
REMOVAL
1. Remove the heater and cooling unit assembly. Refer to
VTL-12, "Removal and Installation"
.
2. Disconnect the harness connector from the intake door motor.
3. Remove the three intake door motor screws and the intake door motor.
INSTALLATION
Installation is in the reverse order of removal.
WJIA1480E
1.
Heater and cooling unit assembly
2.
Intake door motor
3.
Air mix door motor
4.
Variable blower control/Blower motor resistor
5.
Mode door motor
MODE DOOR MOTOR
VTL-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
MODE DOOR MOTOR
Removal and Installation
INFOID:0000000009484342
Mode Door Motor - Heater and Cooling Unit Assembly
REMOVAL
1. Position the front door welt aside.
2. Remove the lower dash side finisher. Refer to
INT-18, "Removal and Installation"
3. Remove the instrument lower panel LH. Refer to
IP-14, "Removal and Installation"
.
4. Remove the BCM. Refer to
BCS-50, "Removal and Installation"
.
5. Disconnect the harness connector from the mode door motor.
6. Remove the three mode door motor screws and the mode door motor.
INSTALLATION
Installation is in the reverse order of removal.
WJIA1480E
1.
Heater and cooling unit assembly
2.
Intake door motor
3.
Air mix door motor
4.
Variable blower control/Blower motor resistor
5.
Mode door motor
VTL-20
< REMOVAL AND INSTALLATION >
AIR MIX DOOR MOTOR
AIR MIX DOOR MOTOR
Removal and Installation
INFOID:0000000009484343
Air Mix Door Motor - Heater and Cooling Unit Assembly
REMOVAL
1. Remove the heater and cooling unit assembly. Refer to
VTL-12, "Removal and Installation"
.
2. Disconnect the harness connector from the air mix door motor.
3. Remove the three air mix door motor screws and the air mix door motor.
INSTALLATION
Installation is in the reverse order of removal.
WJIA1480E
1.
Heater and cooling unit assembly
2.
Intake door motor
3.
Air mix door motor
4.
Variable blower control/Blower motor resistor
5.
Mode door motor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст