Nissan Xterra. Manual — part 113
PRECAUTIONS
BRC-109
< PRECAUTION >
[TYPE 1]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• Area to be repaired must be soldered and wrapped with tape.
Make sure that fraying of twisted wire is within 110 mm (4.33 in).
• Do not make a bypass connection to repaired area. (If the circuit is
bypassed, characteristics of twisted wire will be lost.)
PKIA0306E
PKIA0307E
BRC-110
< PREPARATION >
[TYPE 1]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009482703
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tool
INFOID:0000000009482704
Tool number
(TechMate No.)
Tool name
Description
—
(J-45741)
ABS active wheel sensor tester
Checking operation of ABS active wheel sen-
sors
ST30031000
(
—
)
Bearing puller
Removing sensor rotor
WFIA0101E
ZZA0700D
Tool name
Description
1. Flare nut crowfoot
2. Torque wrench
Removing and installing brake piping
a: 10 mm (0.39 in)/12 mm (0.47 in)
Power tool
Loosening nuts, screws and bolts
S-NT360
PIIB1407E
WHEEL SENSORS
BRC-111
< UNIT REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
UNIT REMOVAL AND INSTALLATION
WHEEL SENSORS
Removal and Installation
INFOID:0000000009482705
REMOVAL
1. Remove the front disc rotor, if removing the front wheel sensor. Refer to
BR-34, "Removal and Installation
of Brake Caliper and Disc Rotor"
.
2. Remove the wheel sensor bolt(s).
3. Pull the wheel sensor straight out, being careful to turn it as little as possible.
CAUTION:
• Be careful not to damage the wheel sensor edge and sensor rotor teeth.
• Do not pull on the wheel sensor harness.
4. Disconnect the wheel sensor harness connector, then remove the wheel sensor harness from the mounts
to remove the wheel sensors.
INSTALLATION
Installation is in the reverse order of removal.
• Before installing the wheel sensors do the following:
- Inspect and replace the wheel sensor if damaged.
- Clean the wheel sensor hole and mating surface with brake cleaner and a lint-free cloth. Be careful that dirt
and debris do not enter the hub and bearing assembly or the rear axle.
1.
Front wheel sensor
2.
Rear wheel sensor (C200)
3.
Rear wheel sensor (M226)
WFIA0339E
BRC-112
< UNIT REMOVAL AND INSTALLATION >
[TYPE 1]
SENSOR ROTOR
SENSOR ROTOR
Removal and Installation
INFOID:0000000009482706
FRONT
The wheel sensor rotors are built into the wheel hubs and are not removable. If damaged, replace wheel hub
and bearing assembly. Refer to
FAX-8, "Removal and Installation"
REAR (C200)
Removal and Installation
It is necessary to disassemble the rear axle to replace the sensor rotor. Perform the axle shaft assembly
removal procedure to replace sensor rotor. Refer to
RAX-8, "Removal and Installation"
.
REAR (M226)
Removal
NOTE:
It is necessary to disassemble the rear axle to replace the sensor rotor.
1. Remove the axle shaft assembly. Refer to
RAX-20, "Removal and Installation"
2. Pull the sensor rotor off of the axle shaft using Tool and a suitable press.
Installation
1. Install the new sensor rotor on the axle shaft using a suitable
length steel tube and a press. Make sure the sensor rotor is fully
seated.
CAUTION:
Do not reuse the sensor rotor.
2. Install the axle shaft assembly. Refer to
.
CAUTION:
Do not reuse the axle oil seal.
Tool number
: ST30031000 (
—
)
WFIA0341E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст