Nissan Xterra. Manual — part 510
MWI
DIAGNOSIS SYSTEM (METER)
MWI-27
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
NOTE:
Some items are not available due to vehicle specification.
*: The monitor will indicate “OFF” even though the brake warning lamp is on if either of the following conditions exist.
• The parking brake is engaged
• The brake fluid level is low
WORK SUPPORT
SET IND [ON/OFF]
X
Displays [ON/OFF] condition of SET indicator.
4WD LOCK SW [ON/OFF]
X
Indicates [ON/OFF] condition of 4WD lock switch.
4WD LOCK IND [ON/OFF]
X
Indicates [ON/OFF] condition of 4WD lock indicator.
4WD W/L [ON/OFF]
X
Displays [ON/OFF] condition of tire 4WD warning lamp.
FUEL CAP W/L [ON/OFF]
X
Displays [ON/OFF] condition of loose fuel cap indicator.
TPMS PRESS L [ON/OFF]
X
Displays [ON/OFF] condition of check tire pressure indicator.
Display item [Unit]
MAIN
SIGNALS
SELECTION
FROM MENU
Description
Work support item
Description
Turn signal buzzer diagnosis
A possible malfunction can be narrowed down by following dis-
played instructions.
Fuel meter diagnosis (Analog pointer)
MWI-28
< DTC/CIRCUIT DIAGNOSIS >
DTC U1000 CAN COMMUNICATION
DTC/CIRCUIT DIAGNOSIS
DTC U1000 CAN COMMUNICATION
DTC Logic
INFOID:0000000009483200
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009483201
Symptom: Displays “CAN COMM CIRC [U1000]” as a self-diagnosis result of combination meter.
1.
CHECK CAN COMMUNICATION
Select “SELF-DIAG RESULTS” mode for “METER/M&A” with CONSULT.
>> Go to “LAN system”. Refer to
LAN-14, "Trouble Diagnosis Flow Chart"
.
DTC
CONSULT display
Detection condition
U1000
CAN COMM CIRC
[U1000]
When combination meter is not receiving CAN communication signals for 2 seconds or more.
MWI
DTC B2205 VEHICLE SPEED CIRCUIT
MWI-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DTC B2205 VEHICLE SPEED CIRCUIT
Description
INFOID:0000000009483202
The ABS actuator and electric unit (control unit) provides a vehicle speed signal to the combination meter via
CAN communication lines.
DTC Logic
INFOID:0000000009483203
Diagnosis Procedure
INFOID:0000000009483204
Symptom: Displays “VEHICLE SPEED CIRC [B2205]” as a self-diagnosis result of combination meter.
1.
CHECK COMBINATION METER INPUT SIGNAL
1. Start engine and select “METER/M&A” on CONSULT.
2. Using “SPEED METER” on “DATA MONITOR”, compare the value of DATA MONITOR with speedometer
pointer of combination meter. Speedometer and DATA MONITOR indications should be close.
Is the inspection result normal?
YES
>> Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
(TYPE 1) or
BRC-145, "CONSULT Function (ABS)"
(TYPE 2).
NO
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
DTC
CONSULT display
Detection condition
B2205
VEHICLE SPEED CIRC
[B2205]
Malfunction is detected when an erroneous speed signal is received for 2 seconds or more.
MWI-30
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER
COMBINATION METER : Diagnosis Procedure
INFOID:0000000009483205
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSES
Check for blown combination meter fuses.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
2.
POWER SUPPLY CIRCUIT CHECK
1. Disconnect combination meter connector M24.
2. Check voltage between combination meter harness connector
M24 terminals 3, 16 and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Check harness for open between combination meter and fuse.
3.
GROUND CIRCUIT CHECK
1. Turn ignition switch OFF.
2. Check continuity between combination meter harness connector
M24 terminals 13, 23 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Check ground harness.
BCM (BODY CONTROL MODULE)
Unit
Power source
Fuse No.
Combination meter
Battery 19
Ignition switch ON or START
14
Terminals
Ignition switch position
(+)
(–)
OFF
ACC
ON
Connector
Terminal
M24
3
Ground
Battery
voltage
Battery
voltage
Battery
voltage
16
0V
0V
Battery
voltage
WKIA3279E
Terminals
Continuity
(+)
(–)
Connector
Terminal
M24
13
Ground
Yes
23
WKIA3280E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст