Nissan Xterra. Manual — part 67
BCS
U1000 CAN COMM CIRCUIT
BCS-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000009482951
LAN-45, "CAN Communication Signal Chart"
DTC Logic
INFOID:0000000009482952
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009482953
1.
PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result” of BCM.
Is “CAN COMM CIRCUIT” displayed?
YES
>> Refer to
LAN-14, "Trouble Diagnosis Flow Chart"
NO
>> Refer to
GI-40, "Intermittent Incident"
.
DTC
CONSULT display de-
scription
DTC Detection Condition
Possible cause
U1000
CAN COMM CIRCUIT
When BCM cannot communicate CAN com-
munication signal continuously for 2 sec-
onds or more.
Any item (or items) of the following listed below is
malfunctioning in CAN communication system.
• Transmission
• Receiving (ECM)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)
BCS-28
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000009482954
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
Is the fuse blown?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit.
NO
>> GO TO 2
2.
CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Terminal No.
Signal name
Fuses and fusible link No.
57
Battery power supply
21 (10A)
70
G (50A)
11
Ignition ACC or ON
4 (10A)
38
Ignition ON or START
1 (10A)
Connector
Terminals
Power
source
Condition
Voltage (V) (Ap-
prox.)
(+)
(-)
M18
11
Ground
ACC
power
supply
Ignition
switch
ACC or
ON
Battery voltage
38
Ground
Ignition
power
supply
Ignition
switch ON
or START
Battery voltage
M20
57
Ground
Battery
power
supply
Ignition
switch
OFF
Battery voltage
70
Ground
Battery
power
supply
Ignition
switch
OFF
Battery voltage
LIIA2415E
BCS
POWER SUPPLY AND GROUND CIRCUIT
BCS-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Inspection End.
NO
>> Repair or replace harness.
BCM
Ground
Continuity
Connector
Terminal
M20
67
Yes
LIIA0915E
BCS-30
< DTC/CIRCUIT DIAGNOSIS >
COMBINATION SWITCH INPUT CIRCUIT
COMBINATION SWITCH INPUT CIRCUIT
Diagnosis Procedure
INFOID:0000000009482955
Regarding Wiring Diagram information, refer to
.
1.
CHECK INTPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect BCM and combination switch.
3. Check continuity between BCM harness connector and combi-
nation switch harness connector.
Does continuity exist?
YES
>> GO TO 2
NO
>> Repair or replace harness.
2.
CHECK INTPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT
Check for continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Repair or replace harness.
NO
>> GO TO 3
3.
CHECK COMBINATION SWITCH
Check combination switch. Refer to
Is the check result normal?
YES
>> Replace BCM. Refer to
BCS-50, "Removal and Installation"
NO
>> Replace combination switch (applicable parts). Refer to
EXL-161, "Removal and Installation"
Special Repair Requirement
INFOID:0000000009482956
1.
ADDITIONAL SERVICE WHEN REPLACING BCM
>> Refer to
BCS-3, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"
.
System
BCM
Combination switch
Continuity
Connector
Terminal
Connector
Terminal
INPUT 1
M18
(A)
36
M28
(B)
1
Yes
INPUT 2
35
2
INPUT 3
34
3
INPUT 4
33
4
INPUT 5
32
5
ALMIA0278ZZ
System
BCM
Ground
Continuity
Connector
Terminal
INPUT 1
M18
36
No
INPUT 2
35
INPUT 3
34
INPUT 4
33
INPUT 5
32
ALMIA0279ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст