Nissan Xterra. Manual — part 680
OIL PAN
TM-233
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2. Install the oil pan with new oil pan gasket.
CAUTION:
• Be sure the oil drain plug is located to the rear of the
transmission assembly.
• Before installing oil pan bolts, remove any traces of old
sealant from the sealing surfaces and threaded holes.
• Do not reuse old gasket, replace with a new one.
• Always replace the oil pan bolts as they are self-sealing.
• Partially install the oil pan bolts in a criss-cross pattern to
prevent dislocation of the gasket.
3. Tighten oil pan bolts in numerical order as shown.
4. Refill the A/T with fluid and check for fluid leakage. Refer to
TM-215, "Checking the A/T Fluid (ATF)"
.
SCIA2308E
Oil pan bolts
: 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA4113E
TM-234
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
CONTROL VALVE WITH TCM
CONTROL VALVE WITH TCM
Removal and Installation
INFOID:0000000009485606
COMPONENTS
REMOVAL
1. Disconnect negative battery terminal. Refer to
PG-72, "Removal and Installation"
2. Drain A/T fluid. Refer to
TM-217, "Changing the A/T Fluid (ATF)"
.
3. Disconnect A/T assembly harness connector.
1.
Transmission
2.
Snap ring
3.
Sub-harness
4.
Control valve with TCM
5.
Bracket
6.
O-ring
7.
Plug
8.
Oil pan gasket
9.
Oil pan bolts
10. Oil pan
11. Magnet
12. Drain plug
13. Drain plug gasket
14. Terminal cord assembly
15. O-ring
A.
For tightening torque, refer to "Installation"
Refer to
AWDIA0890GB
CONTROL VALVE WITH TCM
TM-235
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4. Remove snap ring from A/T assembly harness connector.
5. Push A/T assembly harness connector.
CAUTION:
Do not damage harness connector.
6. Remove oil pan and oil pan gasket. Refer to
TM-232, "Removal and Installation"
.
7. Straighten terminal clip (
) to free the output speed sensor har-
ness.
8. Disconnect output speed sensor harness connector (1).
CAUTION:
Do not damage harness connector.
9. Remove bolts (A), (B) and (C) from control valve with TCM.
SCIA5021E
SCIA5022E
JSDIA1316ZZ
: Front
Bolt symbol
Length mm (in)
Number of bolts
(A)
42 (1.65)
5
(B)
55 (2.17)
6
(C)
40 (1.57)
1
SCIA8074E
TM-236
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
CONTROL VALVE WITH TCM
10. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the manual valve notch and
manual plate height. Remove it vertically.
11. Remove plug (1) with bracket (2) from control valve with TCM.
•
:Bolt
12. Remove the bracket (1) from plug (2).
13. Remove O-ring (1) from plug (2).
CAUTION:
Do not reuse O-ring.
SCIA5142E
JSDIA1311ZZ
JSDIA1312ZZ
JSDIA1313ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст