Nissan Xterra. Manual — part 651
P0705 TRANSMISSION RANGE SENSOR A
TM-117
< DTC/CIRCUIT DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 2.
2.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
DETECT MALFUNCTIONING ITEM
Check the following.
• A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
4.
CHECK SUB-HARNESS
1. Remove control valve with TCM. Refer to
TM-234, "Removal and Installation"
.
2. Disconnect transmission range switch connector and TCM connector.
3. Check continuity between transmission range switch connector
(A) terminals and TCM connector (B) terminals.
4. If OK, check harness for short to ground and short to power.
5. Reinstall any part removed.
OK or NG
OK
>> Replace the control valve with TCM. Refer to
TM-234, "Removal and Installation"
NG
>> Replace open circuit or short to ground and short to power in harness or connectors.
5.
CHECK DTC
Perform “DTC Confirmation Procedure”.
• Refer to
TM-116, "DTC Confirmation Procedure"
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
Item
Connector
Terminal
Continuity
Transmission range switch con-
nector
F505
1
Yes
TCM connector
F503
13
Transmission range switch con-
nector
F505
2
Yes
TCM connector
F503
11
Transmission range switch con-
nector
F505
3
Yes
TCM connector
F503
12
Transmission range switch con-
nector
F505
5
Yes
TCM connector
F503
14
JSDIA1328GB
TM-118
< DTC/CIRCUIT DIAGNOSIS >
[5AT: RE5R05A]
P0717 INPUT SPEED SENSOR A
P0717 INPUT SPEED SENSOR A
Description
INFOID:0000000009485437
The input speed sensor detects input shaft rpm (revolutions per minute). It is located on the input side of the
automatic transmission. Monitors revolution of sensor 1 and sensor 2 for non-standard conditions.
CONSULT Reference Value in Data Monitor Mode
INFOID:0000000009485438
On Board Diagnosis Logic
INFOID:0000000009485439
• This is an OBD-II self-diagnostic item.
• Diagnostic trouble code “P0717” with CONSULT or 11th judgment flicker without CONSULT is detected
under the following conditions.
- When TCM does not receive the proper voltage signal from the sensor.
- When TCM detects an irregularity only at position of 4GR for input speed sensor 2.
Possible Cause
INFOID:0000000009485440
• Harness or connectors
(The sensor circuit is open or shorted.)
• Input speed sensor 1, 2
DTC Confirmation Procedure
INFOID:0000000009485441
CAUTION:
• Always drive vehicle at a safe speed.
• Be careful not to rev engine into the red zone on the tachometer.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT.
3. Start engine and maintain the following conditions for at least 5 consecutive seconds.
VHCL/S SE-AT: 40 km/h (25 MPH) or more
ENGINE SPEED: 1,500 rpm or more
ACCELE POSI: 0.5/8 or more
SLCT LVR POSI: “D” position
GEAR (Input speed sensor 1): 4th or 5th position
GEAR (Input speed sensor 2): All position
Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.
4. If DTC is detected, go to
.
WITH GST
Follow the procedure “WITH CONSULT”.
Diagnosis Procedure
INFOID:0000000009485442
1.
CHECK INPUT SIGNAL
With CONSULT
1. Start engine.
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT.
3. Drive vehicle and read out the value of “INPUT SPEED”.
Item name
Condition
Display value (rpm)
INPUT SPEED
During driving (lock-up ON)
Approximately matches the engine speed.
P0717 INPUT SPEED SENSOR A
TM-119
< DTC/CIRCUIT DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 2.
2.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
DETECT MALFUNCTIONING ITEM
Check the following.
• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the control valve with TCM. Refer to
TM-234, "Removal and Installation"
NG
>> Repair or replace damaged parts.
4.
CHECK DTC
Perform “DTC Confirmation Procedure”.
• Refer to
TM-118, "DTC Confirmation Procedure"
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
TM-120
< DTC/CIRCUIT DIAGNOSIS >
[5AT: RE5R05A]
P0720 OUTPUT SPEED SENSOR
P0720 OUTPUT SPEED SENSOR
Description
INFOID:0000000009485443
The output speed sensor detects the revolution of the parking gear and emits a pulse signal. The pulse signal
is sent to the TCM which converts it into vehicle speed.
CONSULT Reference Value in Data Monitor Mode
INFOID:0000000009485444
On Board Diagnosis Logic
INFOID:0000000009485445
• This is an OBD-II self-diagnostic item.
• Diagnostic trouble code “P0720” with CONSULT or 1st judgment flicker without CONSULT is detected under
the following conditions.
- When TCM does not receive the proper voltage signal from the sensor.
- After ignition switch is turned “ON”, irregular signal input from vehicle speed signal before the vehicle starts
moving.
Possible Cause
INFOID:0000000009485446
• Harness or connectors
(The sensor circuit is open or shorted.)
• Output speed sensor
• Vehicle speed signal
DTC Confirmation Procedure
INFOID:0000000009485447
CAUTION:
• Always drive vehicle at a safe speed.
• Be careful not to rev engine into the red zone on the tachometer.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT.
3. Drive vehicle and check for an increase of “VHCL/S SE-A/T” value in response to “VHCL/S SE-MTR”
value.
If the check result is NG, go to
If the check result is OK, go to following step.
4. Select “DATA MONITOR” mode for “ENGINE” with CONSULT.
5. Start engine and maintain the following conditions for at least 5 consecutive seconds.
VHCL/S SE-AT: 30 km/h (19 MPH) or more
ACCELE POSI: More than 1.0/8
SLCT LVR POSI: “D” position
Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.
If the check result is NG, go to
If the check result is OK, go to following step.
6. Maintain the following conditions for at least 5 consecutive seconds.
ENGINE SPEED: 3,500 rpm or more
ACCELE POSI: More than 1.0/8
SLCT LVR POSI: “D” position
Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.
If the check result is NG, go to
Item name
Condition
Display value (km/h)
VHCL/S SE-A/T
During driving
Approximately matches the speedometer reading.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст