Nissan Xterra. Manual — part 568
PREPARATION
RAX-5
< PREPARATION >
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
Tool name
Description
1 Flare nut crowfoot
2 Torque wrench
Removing and installing each brake piping
a: 10 mm (0.39 in)
Bearing cage oil seal drift
Installing oil seal
a: 74 mm (2.91 in) dia.
b: 68 mm (2.68 in) dia.
Rear axle oil seal drift
Installing oil seal
a: 54.5 mm (2.15 in.)
b: 34.5 mm (1.36 in.)
Power tool
Loosening nuts, screws and bolts
S-NT360
NT115
NT115
PIIB1407E
RAX-6
< SYMPTOM DIAGNOSIS >
[C200]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009484501
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
Possible cause and SUSPECTED PARTS
Imp
rop
er i
ns
ta
lla
tio
n,
lo
os
en
es
s
Part
s interf
erence
Whe
e
l be
ari
n
g da
ma
ge
PROPELLER SHAFT
REAR FINAL
DRIVE
SUSPE
N
S
ION
TI
RE
S
ROAD WHEE
L
BRAKE
S
Symptom
Noise
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Shudder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
×
ON-VEHICLE SERVICE
RAX-7
< REMOVAL AND INSTALLATION >
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REMOVAL AND INSTALLATION
ON-VEHICLE SERVICE
Rear Axle Parts
INFOID:0000000009484502
• Check the axle parts for excessive play, wear and damage. Replace as necessary.
• Shake each rear wheel to check for excessive play. Repair as nec-
essary.
• Retighten all nuts and bolts to the specified torque. Refer to
Rear Axle Bearing
INFOID:0000000009484503
• Check that the axle shaft bearing operates smoothly. Replace as necessary.
• Check axial end play. Refer to
SMA525A
RAX-8
< UNIT REMOVAL AND INSTALLATION >
[C200]
AXLE SHAFT
UNIT REMOVAL AND INSTALLATION
AXLE SHAFT
Removal and Installation
INFOID:0000000009484504
CAUTION:
Before removing the rear axle, disconnect the wheel sensor from the assembly. Then move it away
from the axle. Failure to do so may result in damage to the sensor wires and the sensor becoming
inoperative.
• Wheel bearing does not require maintenance.
• If growling noise is emitted from wheel bearing during operation, replace wheel bearing assembly.
1.
Axle shaft
2.
Grease catcher
3.
Wheel stud
4.
Axle bearing stud
5.
Back plate and torque member
6.
Axle bearing
7.
Bearing ring retainer
8.
Shim washer
9.
Snap ring
10. Wheel sensor rotor
11. O-ring
12. Axle oil seal
13. Breather
14. Rear final drive
WDIA0280E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст