Nissan Xterra. Manual — part 722
WT-50
< UNIT REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
UNIT REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
Exploded View
INFOID:0000000009483107
Transmitter (Pressure Sensor)
INFOID:0000000009483108
REMOVAL
1. Remove wheel and tire using power tool. Refer to
2. Remove valve cap and valve core to deflate the tire.
NOTE:
If the tire is to be reused, apply a matching mark on the tire in line with the position of the road wheel valve
stem assembly for the purpose of road wheel and tire balance adjustment after installation.
3. Remove the valve stem nut and allow transmitter to fall into tire.
4. Lubricate the tire outside bead well with a suitable non-silicone lubricant, and remove outside of tire from
the road wheel. Reach inside the tire and remove the transmitter.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and road wheel.
• Be sure not to damage the road wheel or transmitter.
• Do not allow lubricant to make contact with transmitter.
5. Lubricate the tire inside bead well with a suitable non-silicone lubricant, and remove inside of tire from the
road wheel.
1.
Transmitter (tire pressure sensor)
2.
O-ring
3.
Valve stem nut
4.
Valve core
5.
Valve cap
6.
Valve stem assembly
:
Parts that are replaced as a set when the tire is replaced.
AWEIA0212GB
SEIA0047E
REMOVAL AND INSTALLATION
WT-51
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and road wheel.
• Be sure not to damage the road wheel.
6. Remove the valve stem from the transmitter as shown.
INSTALLATION
1. Apply a suitable non-silicone lubricant to the tire inside bead.
CAUTION:
Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.
2. Install the tire inside bead (1) onto the road wheel (2) in the posi-
tion shown.
3. Install the valve stem to the transmitter.
4. Install the O-ring to the transmitter.
CAUTION:
• Do not reuse O-ring.
• Insert O-ring to the base of the transmitter.
• The base of the valve stem (A) must be positioned in the
groove of the metal plate as shown.
JSEIA0378ZZ
JPEIC0105ZZ
JSEIA0376GB
WT-52
< UNIT REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
5. Install transmitter (1) to road wheel while pressing at position
(A).
CAUTION:
• Check that O-ring contacts horizontally with road wheel.
• Check that the base of the valve stem is positioned in the
groove of the metal plate.
6. Install and tighten the valve stem nut to the specified torque.
CAUTION:
Do not use power tool for installation.
7. Place wheel on turntable of tire machine. Ensure that transmitter
is 270 degrees from mounting/dismounting head.
NOTE:
Do not touch transmitter with mounting head.
8. Apply a suitable non-silicone lubricant to the tire outside bead.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will
deteriorate the tire and wheel.
• Do not allow lubricant to make contact with transmitter.
9. Install the tire outside bead onto the road wheel as normal.
NOTE:
If the tire is being reused, align the matching mark applied on
the tire with the position of the road wheel valve stem assembly for the purpose of road wheel and tire bal-
ance adjustment after installation. Ensure that the tire does not rotate relative to road wheel.
10. Install the valve core and inflate tire.
CAUTION:
Do not reuse valve core.
11. Install the valve cap.
CAUTION:
Do not reuse valve cap.
12. Inflate tire and balance the wheel and tire assembly. Refer to
.
13. Install wheel and tire assembly in appropriate wheel position on vehicle. Refer to
.
NOTE:
If replacing the transmitter, then transmitter wake up operation must be performed. Refer to
14. Adjust neutral position of steering angle sensor. Refer to
BRC-115, "Removal and Installation"
.
JSEIA0377ZZ
Valve stem nut
tightening torque
: 7.7 N·m (0.79 kg-m, 68 in-lb)
WEIA0046E
SERVICE DATA AND SPECIFICATIONS (SDS)
WT-53
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Road Wheel
INFOID:0000000009483109
Tire
INFOID:0000000009483110
Unit: kPa (kg/cm
2
, psi)
Wheel type
Aluminum
Steel
Inside
Outside
Maximum runout limit
Lateral mm (in)
0.3 (0.012) or less
0.8 (0.031) or less
0.8 (0.031) or less
Radial mm (in)
0.3 (0.012) or less
0.6 (0.024) or less
0.6 (0.024) or less
Maximum allowable
imbalance
Dynamic (at rim flange)
Less than 5 g (0.18 oz) (per side)
Static (at rim flange)
Less than 10 g (0.35 oz)
Tire size
Air pressure
Conventional tire
Spare tire
2WD
4WD
P265/70R16
250 (2.5, 36)
240 (2.4, 35)
240 (2.4, 35)
P265/75R16
240 (2.4, 35)
240 (2.4, 35)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст