Nissan Xterra. Manual — part 356
EM-52
< REMOVAL AND INSTALLATION >
[VQ40DE]
FRONT TIMING CHAIN CASE
7. Remove power steering oil pump from bracket with piping connected, and temporarily secure it aside.
ST-17, "Removal and Installation"
8. Remove power steering oil pump bracket. Refer to
ST-17, "Removal and Installation"
9. Remove generator. Refer to
CHG-27, "Removal and Installation"
.
10. Remove water bypass hoses and water hose clamp.
11. Remove engine cooling fan (Crankshaft driven type) and fan bracket. Refer to
Installation (Crankshaft driven type)"
.
12. Remove water hose at oil cooler.
13. Remove oil cooler water bypass pipe from front timing chain case. Refer to
.
14. Remove right and left intake valve timing control covers.
• Loosen bolts in reverse order as shown.
• Cut liquid gasket for removal using Tool.
CAUTION:
• Shaft is internally jointed with camshaft sprocket (INT)
center hole. When removing, keep it horizontal until it is
completely disconnected.
• Do not damage the mating surfaces.
15. Remove collared O-rings from front timing chain case (left and
right side).
CAUTION:
Do not reuse O-rings.
16. Remove A/C compressor bolts and temporarily secure A/C compressor aside. Refer to
and Installation of Compressor"
.
17. Remove crankshaft pulley as follows:
a. Remove access plate and install Ring Gear Stopper Tool.
b. Loosen crankshaft pulley bolt so that there is a 10 mm (0.39 in)
gap between bolt and crankshaft pulley.
CAUTION:
Do not remove crankshaft pulley bolt. Keep loosened
crankshaft pulley bolt in place to protect the crankshaft pul-
ley from dropping.
c.
Pull crankshaft pulley with both hands to remove it.
Tool number
: KV10111100 (J-37228)
SEM728G
PBIC2631E
Tool number
: KV11105210 (J-44716)
PBIC2918E
FRONT TIMING CHAIN CASE
EM-53
< REMOVAL AND INSTALLATION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
18. Loosen two bolts in front of oil pan (upper) in reverse order as
shown.
19. Remove front timing chain case as follows:
a. Loosen bolts with power tool in reverse order as shown.
b. Insert suitable tool into the notch at the top of the front timing
chain case as shown (1).
c. Pry off case by moving tool as shown (2).
• Cut liquid gasket for removal using Tool.
CAUTION:
• Do not use screwdriver or something similar.
• After removal, handle front timing chain case carefully so
it does not twist, bend, or warp under a load.
• Do not damage the mating surface.
20. Remove O-rings from rear timing chain case.
CAUTION:
Do not reuse O-rings.
21. If necessary, remove water pump cover and chain tensioner cover from front timing chain case.
• Cut liquid gasket for removal using Tool.
CAUTION:
Do not damage the mating surfaces.
PBIC2907E
PBIC2908E
Tool number
: KV10111100 (J-37228)
SEM156F
PBIC2548E
Tool number
: KV10111100 (J-37228)
EM-54
< REMOVAL AND INSTALLATION >
[VQ40DE]
FRONT TIMING CHAIN CASE
22. Remove front oil seal from front timing chain case using suitable
tool.
CAUTION:
Be careful not to damage front timing chain case.
23. Remove idler pulley, if necessary. Refer to
EM-14, "Drive Belt Auto-Tensioner and Idler Pulley"
24. Use a scraper to remove all traces of old liquid gasket from front
and rear timing chain cases, oil pan (upper), and liquid gasket
mating surfaces.
CAUTION:
Be careful not to allow gasket fragments to enter oil pan.
• Remove old liquid gasket from bolt hole and thread.
25. Use a scraper to remove all traces of old liquid gasket from
water pump cover, chain tensioner cover (if necessary) and
intake valve timing control covers.
INSTALLATION
PBIC2909E
PBIC2910E
PBIC2084E
SEM926E
FRONT TIMING CHAIN CASE
EM-55
< REMOVAL AND INSTALLATION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
1. Hammer dowel pins (right and left) into front timing chain case
up to a point close to taper in order to shorten protrusion length.
NOTE:
Be sure to place dowel pins in the original holes in front timing
chain case.
2. Install new front oil seal on the front timing chain case.
• Apply new engine oil to both oil seal lip and dust seal lip.
• Install it so that each seal lip is oriented as shown.
• Press-fit oil seal until it becomes flush with front timing chain
case end face using suitable drift [outer diameter: 60 mm (2.36
in)].
• Make sure the garter spring is in position and seal lip is not
inverted.
CAUTION:
• Be careful not to damage front timing chain case and
crankshaft.
• Press-fit straight and avoid causing burrs or tilting oil
seal.
3. Install water pump cover and chain tensioner cover to front timing chain case, if removed.
• Apply a continuous bead of liquid gasket using Tool to front
timing chain case as shown.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-21, "Recommended Chemical Products and Sealants"
.
4. Install idler pulley, if removed.
5. Install front timing chain case as follows:
PBIC2615E
SEM715A
PBIC2911E
Tool number
: WS39930000 (
—
)
PBIC2912E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст