Nissan Xterra. Manual — part 580
LATCH (LOWER ANCHORS AND TETHER FOR CHILDREN) SYSTEM
SB-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
LATCH (LOWER ANCHORS AND TETHER FOR CHILDREN) SYSTEM
Removal and Installation
INFOID:0000000009485359
NOTE:
The LATCH (Lower Anchors and Tether for Children) system is not serviceable.
SB-12
< REMOVAL AND INSTALLATION >
TOP TETHER STRAP CHILD RESTRAINT
TOP TETHER STRAP CHILD RESTRAINT
Removal and Installation
INFOID:0000000009485360
NOTE:
The Top Tether Strap Child Restraint system is not serviceable.
SE-1
BODY INTERIOR
C
D
E
F
G
H
I
K
L
M
SECTION
SE
A
B
SE
N
O
P
CONTENTS
SEAT
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tools . . . . . . . . . ...
CLIP LIST . . . . . . . . . . . . . . .
Descriptions for Clips . . . . . . . . . . . ....
WIRING DIAGRAM . . . . . . . . . ...
HEATED SEAT . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .....
SYMPTOM DIAGNOSIS . . . . . . . ..
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . ..
Work Flow . . . . . . . . . . . . . . . .
Generic Squeak and Rattle Troubleshooting . . ...
Diagnostic Worksheet . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
FRONT SEAT . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
REAR SEAT . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
FRONT SEAT . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
REAR SEAT . . . . . . . . . . . . . ..
SE-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010211627
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Work
INFOID:0000000010202689
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст